Bazooka 4-Channel 240W Amplifier (BA460) Car Audio Amplifier - Answered Questions & Fixed issues
I bought a 4 channel
why aren't you running rca's from the deck to your amp?
12/30/2010 12:00:45 AM •
Bazooka...
•
Answered
on Dec 30, 2010
•
140 views
Bt8250d is cutting out
Loose connection or your power cable and earth cable to your amp are not a heavy enough gauge.
11/30/2014 4:34:44 PM •
Bazooka Car...
•
Answered
on Nov 30, 2014
•
112 views
Speaker Fried, is my Amp toast too?
You are sending TOO much power to the speakers, Replace the speakers and then get a much smaller amp that is within the ratings of the speakers. ACTUALLY you should get an amp that is aboout 1/2 the total rating of the speakers.
You should ALSO procure a sound meter to verify the sound level is within safe limits. If you insist upon abusing your ears with too high a sound pressure, be ready to buy hearing aids at a VERY young age.
You also need to know that the enclosure of the speaker plays a part in keeping the speaker from tearing itself to pieces.
MANY of the auto sound system installers are hacks that don't do it right and you see what happens to your expensive equipment!
Using even a Radio Shack sound meter properly will protect your preciuos hearing for later life.
12/22/2009 9:19:21 PM •
Bazooka Car...
•
Answered
on Dec 22, 2009
•
152 views
Bazooka amp
If the amp is in protect mode, it probably has shorted output transistors. To eliminate other possible problems, do the following. I'll assume that you've checked the amplifier's on-board fuses.
With your multimeter set to DC volts, the black meter lead on the ground terminal of the amp (not on the point where the ground wire connected to the vehicle) and the head unit on (so the amp will have remote voltage applied), touch the red lead alternately to the B+ and remote terminals of the amp. If the voltage is below ~11 volts, you need to check the wiring feeding whichever line is too low.
Disconnect all speaker wires from the speaker terminals of the amp and disconnect signal cables from the amp. If it powers up, the wiring needs to be checked. If it remains in protect mode, the amp almost certainly has shorted output transistors and will need to be repaired.
6/15/2008 6:52:48 PM •
Bazooka Car...
•
Answered
on Jun 15, 2008
•
693 views
We have car audio that requires code, do you know the options how to unlock it?
If your car audio system requires a code to unlock it, there are a few options you can try:
Check the user manual: The user manual for your car audio system may contain information on how to unlock it if a code is required. Look for a section on "security" or "anti-theft" features.
Contact the manufacturer: If you don't have the user manual or can't find the information you need, you can try contacting the manufacturer of the car audio system. They may be able to provide you with the code or instructions on how to unlock it.
Try common codes: Some car audio systems use a default code, such as 0000 or 1234. Try entering these codes to see if they work.
Reset the system: If none of the above options work, you may need to reset the car audio system. This will erase any saved settings and data, including the code. The process for resetting the system will vary depending on the make and model of your car and audio system. Check the user manual or contact the manufacturer for instructions.
3/17/2023 10:03:22 AM •
Car Audio &...
•
Answered
on Mar 17, 2023
•
25 views
Proton D940 stereo receiver. What kind of CD player and cables do I need to hook it up to the car?
The Proton D940 stereo receiver features both analog and digital inputs, so you have a few options when it comes to connecting a CD player to the receiver.
For a digital connection, you will need a CD player with a digital output, such as a coaxial or optical output, and a digital cable to connect the two. Look for a CD player with a digital output labeled "coaxial" or "optical" and purchase a cable that matches the output on the CD player and the input on the receiver.
For an analog connection, you will need a CD player with analog outputs, such as RCA outputs, and an RCA cable to connect the two. Look for a CD player with an analog output labeled "RCA" and purchase an RCA cable with the appropriate connectors to match the CD player and the receiver.
Once you have the CD player and cables, connect the CD player to the Proton D940 stereo receiver using the appropriate input on the back of the receiver. If you are using a digital connection, select the appropriate digital input on the receiver using the input selector button on the front of the receiver. If you are using an analog connection, select the appropriate analog input using the same input selector button.
3/15/2023 4:29:43 AM •
Car Audio &...
•
Answered
on Mar 15, 2023
•
13 views
Cq-vd6505u Car DVD
You can try to hold the right round selector knob to the right for 10 seconds while unit is on asking for code input. That will work to unlock if the previous owner did not set the 4 digit code. Good Luck
3/11/2023 10:56:58 PM •
Car Audio &...
•
Answered
on Mar 11, 2023
•
258 views
How do I reset a TRP am/fm cd player. When i turn it on it says P55 2001
This is an old question but I recently had the same problem. The owners manual says to press and hold the band and preset 1 buttons simultaneously. This did not work for me. I removed the radio from the dash and pulled the fuse on the back of the radio. Replacing it after a few seconds reset the radio.
3/6/2023 2:41:06 PM •
Car Audio &...
•
Answered
on Mar 06, 2023
•
249 views
My pure cd player keeps changing source to AUX. How do I stop this from happening.
If your Pure CD player keeps changing source to AUX, it may be due to a few different reasons. Here are some troubleshooting steps you can try:
- Check the connections: Make sure that the cables connecting your CD player to your speakers or amplifier are securely plugged in. Loose or faulty connections can cause interruptions in the signal and trigger the player to switch to AUX mode.
- Clean the input selector switch: If your CD player has an input selector switch, dust and debris may accumulate over time and cause the switch to malfunction. Clean the switch using a can of compressed air or a soft-bristled brush.
- Check the settings: Some CD players may have settings that automatically switch to AUX mode when no signal is detected from the CD player. Check your user manual to see if your CD player has this feature and how to turn it off.
- Reset the CD player: Turn off your CD player and unplug it from the power source for a few minutes. Then, plug it back in and turn it on to see if the issue is resolved.
- Contact the manufacturer: If none of the above solutions work, it may be necessary to contact the manufacturer's customer support for further assistance. They may be able to provide additional troubleshooting steps or arrange for a repair or replacement of your CD player if necessary.
Note: Before attempting any maintenance or repair work on your CD player, be sure to read the user manual thoroughly and follow any safety precautions.
2/28/2023 5:09:10 AM •
Car Audio &...
•
Answered
on Feb 28, 2023
•
39 views
It i stuck on the cd button and I can not get it to change
If your device is stuck on the CD button and you're unable to change it, try the following steps:
- Check the device's manual: First, consult the manual for your device to see if there are any specific instructions for changing the input source. Some devices may require a particular button sequence or menu selection to switch inputs.
- Power cycle the device: Turn off the device and unplug it from the power source for a few minutes. Then, plug it back in and turn it on again. This may help to reset the device and allow you to change the input source.
- Check the remote control: Ensure that the batteries in the remote control are working properly and that you are using the correct remote control for the device. Some devices may require a specific remote control to change inputs.
- Try a different input: If you're unable to change the input from the CD button, try selecting a different input button such as the radio or auxiliary input. This may help to reset the device and allow you to change the input source.
- Contact the manufacturer: If none of the above steps work, contact the manufacturer for assistance. They may be able to provide additional troubleshooting steps or suggest repairs or replacement options.
Hopefully, one of these steps will help you resolve the issue and allow you to change the input source on your device.
2/27/2023 10:52:22 PM •
Car Audio &...
•
Answered
on Feb 27, 2023
•
22 views
Does anyone have schematic for audiotrak 500 amplifier?
I don't have access to specific schematics for the Audiotrak 500 amplifier. However, there are a few options you can try to obtain the schematic:
- Check the manufacturer's website: The first place to look for a schematic is the manufacturer's website. Most manufacturers provide support documentation, including schematics, for their products on their website.
- Contact the manufacturer: You can also try contacting the manufacturer directly and asking if they can provide you with a schematic for the Audiotrak 500 amplifier. They may be able to provide you with the schematic or direct you to a source where you can obtain it.
- Search online: You can also try searching for the schematic online using search engines like Google or Bing. Enter the model number of the Audiotrak 500 amplifier along with the term "schematic," and you may find a PDF version of the schematic available for download.
- Consult with a professional: If you're not able to obtain the schematic through these methods, you can consult with a professional, such as an electronics repair technician. They may have access to the schematic or be able to assist you in troubleshooting the amplifier without the schematic.
I hope these options are helpful in your search for the schematic for the Audiotrak 500 amplifier.
Does anyone have schematic for audiotrak 500 amplifier?
I'm sorry, but as an AI language model, I don't have access to specific schematics for the Audiotrak 500 amplifier. However, there are a few options you can try to obtain the schematic:
- Check the manufacturer's website: The first place to look for a schematic is the manufacturer's website. Most manufacturers provide support documentation, including schematics, for their products on their website.
- Contact the manufacturer: You can also try contacting the manufacturer directly and asking if they can provide you with a schematic for the Audiotrak 500 amplifier. They may be able to provide you with the schematic or direct you to a source where you can obtain it.
- Search online: You can also try searching for the schematic online using search engines like Google or Bing. Enter the model number of the Audiotrak 500 amplifier along with the term "schematic," and you may find a PDF version of the schematic available for download.
- Consult with a professional: If you're not able to obtain the schematic through these methods, you can consult with a professional, such as an electronics repair technician. They may have access to the schematic or be able to assist you in troubleshooting the amplifier without the schematic.
I hope these options are helpful in your search for the schematic for the Audiotrak 500 amplifier.
2/27/2023 2:39:22 PM •
Car Audio &...
•
Answered
on Feb 27, 2023
•
29 views
Why won't my front speKers play on my avh 200e x?
There could be several reasons why your front speakers are not playing on your AVH 200EX. Here are some possible causes:
- Wiring issues: Check the wiring connections between the receiver and the front speakers. Make sure that the wires are properly connected and that there are no loose connections.
- Speaker settings: Check the speaker settings on your receiver to make sure that the front speakers are enabled and set to the correct size and frequency response.
- Balance and fader settings: Check the balance and fader settings on your receiver to make sure that the front speakers are not set to a low level or muted.
- Amplifier issues: If you have an external amplifier, check to make sure that it is properly connected and powered on.
- Speaker problems: If the front speakers are still not playing, there may be an issue with the speakers themselves. Check to see if the speakers are damaged or if the wiring connections are loose.
If none of these steps resolve the issue, you may need to consult with a professional or contact the manufacturer for further assistance.
2/23/2023 11:40:36 AM •
Car Audio &...
•
Answered
on Feb 23, 2023
•
19 views
Not finding what you are looking for?
