Top 20 Mitsubishi WD62628 62" Projection HDTV Questions & Answers

there are several connectors in sockets along the one edge of the screen 6 in your case i think. one might need a little clean an reseat

Mitsubishi... | 42 views | 1 helpful votes

Look for socket to be bent or moved out of position---happens when replacement lamp is installed.

Mitsubishi... | 820 views | 1 helpful votes

IS the set sitting on a flat surface that completely supports the base at the bottom and is level?

Do a little experiment, with set on lift up on either side of the cabinet at the bottom and see if picture gets straight--not a joke or a prank.

Mitsubishi... | 95 views | 0 helpful votes

A simple way to maybe know is Google each model number with "lamp" and unless the replacement being sold is exactly the same number they will not work for each other.

Mitsubishi... | 32 views | 0 helpful votes

Double check when lamp went in it engaged the socket (2 pin) correctly and went all the way in----this is where to begin-------whenever you replace a part on a TV or a car etc and suddenly have a new issue suspect something happened when you replaced that part........

Mitsubishi... | 52 views | 0 helpful votes

The set may not determine 4x3 or 16x9(full) but the box if used and the program may determine this----aspect button if there should try to change this.

Mitsubishi... | 40 views | 0 helpful votes

For the model indicated (WD-62638) the entire screen unit needs to be removed.

Some models had two mirrors--the usual large one in back and a tiny one in the bottom front.

1. Locate and remove front plate below screen (where you may access the lamp as most of these are taken out from front)

2. Remove all the screws ON THE BACK OF THE SET around the top and both sides.

3. Remove a plate behind the removed lower front grill and there you should find a set of wires that go to front keyboard.

4. With that done look carefully at either front side below the screen unit---one screw on either side---do not remove but just back them out.

5. 2 person job---the entire screen unit lifts up and out.

6. DO NOT try to clean the large mirror---if touched with hand or your hair it will smudge and it will show in the picture.

7. If the little mirror is there at the bottom---it can be cleaned with glass cleaner---

8. Insert the screen unit back with the two front lower screws supporting it (have someone hold it in place until you line up and install all all the rear and then the 2 front screws.

Let me know if you have questions.

Mitsubishi... | 217 views | 1 helpful votes

Here's what I would do first. Unplug the satellite receiver and TV from the wall outlet, then plug them both back in and allow them to reboot. Once they have rebooted, see if you have sound. If not, you may have to call the satellite provider for furthur troubleshooting. Also,do you have anything else hooked to your TV with HDMI? (DVD or Blu-Ray player for instance?) Do these work properly? If so, I would assume you have a problem in your satellite receiver. If not, you have a problem in the TV.

Mitsubishi... | 66 views | 0 helpful votes

Please click HERE to download training manual of WD-62628 that has all required info about troubleshooting. Training manual usually made for techs to understand that how tv circuit board work.
Hope this will help.

Mitsubishi... | 403 views | 1 helpful votes

you've got to get a bright light and a mirror if needed to see what is in your way. if the old one won't go back in then something is blocking you out. did you have to get any special angle to remove the original? it may only go in one way and take your time and try different angles

Mitsubishi... | 67 views | 0 helpful votes

I have the same problem, and all I did was replace the bulb and housing the picture is not a true horizontal, the picture is tilted to the right....Any ideas>>??

Mitsubishi... | 128 views | 0 helpful votes

If your set is like mine hold menu & device for 5 seconds and you will get an error code.

Mitsubishi... | 42 views | 0 helpful votes

I had a similar problem with my 42 in Philips LCD HDTV.

Here was the problem. My Power Supply Board had several bad capacitors. I opened my TV (warranty was expired of course) and found four bulged capacitors on the PSB. Many major electronics companies Philips/Magnavox, Sony, Panasonic, and others were sold capacitors that failed in 2-5 years instead of 10-20. The capacitors fail prematurely due to a lack of preservatives. Unfortunately, they were installed in all sorts of devices and cause a wide range of failure problems.

Here are some options for you.

1. Have it fixed by a professional $$$$$$$??????? (Is it under warranty?)

2. Open your TV and find PSB. (The board that the power cord plugs into) Check for faulty caps. If you find some (bulged or leaking) bad caps replace the entire board. The entire board costs around $250 right now because they are in high demand right now. They can be found at but supplies are limited. I would definitely shop around though.

3. Remove and then replace individual faulty caps. This takes some soldering skill.

Caps are inexpensive and if you can take care of it yourself it will save you hundreds.

This may be your problem. If you determine that it might be.

I have a Tip/How TO tutorial on this site that may also help. It gives step by step instructions for replacing caps on PSB #715t2432-2. If this is your board you are in luck. Here is the Link: Fixing the Philips Turns/shuts off on its own problem. I'm working on uploading pictures to help guide people though the process as well. Let me know if I can do anything to help.

Hope this helps and if it does please rate it accordingly. Good luck.

Mitsubishi... | 155 views | 0 helpful votes

my first instinct on this is the mirror inside has come loose. or possibly brpken. can you describe the picture. angled down? let me know how it goes

Mitsubishi... | 22 views | 0 helpful votes

When did you replaced lamp in tv last time?
If lamp has not been replaced in last 2-3 years then its time to get it replaced as weak lamp, that has reached to end of working life, can cause that symptoms in tv.
Let me know if you have additional question.

Mitsubishi... | 317 views | 1 helpful votes

the blinking light signifies to a repair technician with capacitors or circuits are having an issue they can diagnose the problem via the amount of blinks in between pauses however it will require a technician and some specific tools and schematics to fix and it may be cheaper if its no longer under warranty to purchase a new one

Hope this helped

Mitsubishi... | 125 views | 0 helpful votes

Reset the tv by pressing menu and 2470 then enter. If this doesn not fix then you have either a bad e2p or dm.

Mitsubishi... | 440 views | 5 helpful votes

usually it's the "steady sound" or something along that type of name.  maybe auto level.  needs to be turned OFF

Mitsubishi... | 52 views | 0 helpful votes

Your convergence is off. See the owners manual or call tech support to walk you through a convergence.

Mitsubishi... | 90 views | 1 helpful votes

Not finding what you are looking for?
Mitsubishi WD62628 62" Projection HDTV Logo

62 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1258 Answers

The Knight
The Knight

Level 3 Expert

76416 Answers

Todd Hill
Todd Hill

Level 2 Expert

433 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

WD Mitsubishi

  • WD Mitsubishi

Most Popular Question

black lines come go not stay all time

  • Televison & Video