20 Most Recent Denon Dn-X1500 Professional DJ Mixer System Questions & Answers

DISASSEMBLING SERVICE MODE AND POWER SUPPLY CIRCUIT

DISASSEMBLING
(Follow the procedure below in reverse order when reassembling.)
1. Top Panel Unit
(1) Remove 9 side screws and pull up the Top Panel Unit.
(2) Disconnect FFC cable and Connector.
(3) Detach Top Panel Unit
Note : Do not pull out aslant to prevent FFC cable damage.
Do not fail to pull AC cord from wall outlet before disconnect the FFC cable.
If AC cord is remained plugged into wall outlet,
power is kept supplied in the unit, which may cause
danger.

For more check the following link
http://electro-medical.blogspot.in/

on Feb 24, 2015 | Denon Dn-X1500 Professional DJ...

1 Answer

Denon-x1500 not able to find sofware for windows 7

Just log in on the denon dj site and you can get the latest firmware and driver and manual. Read it and everything you need to know
is listed in the manual
gr. richard

Denon Dn-X1500... | Answered on Sep 29, 2014

1 Answer

How do i connect my laptop to denon dn-x1500s?

just download the driver from the site and select him as soundcard, but read first the manual

Denon Dn-X1500... | Answered on Sep 29, 2014

0 Answers

Denon Dn-X1500... | Answered on May 06, 2013

0 Answers

Up version

Denon Dn-X1500... | Posted on Apr 18, 2013 | Be the first to answer

0 Answers

Why is my Denon DN-X1500 showing a version up

Denon Dn-X1500... | Posted on Jun 25, 2010 | Be the first to answer

1 Answer

Headphone cue buttons on dnx 1500 not working and

pulled the cover plate off cleaned switches with freeon put back 2getha all sweet but 4 how long i don't know thanks any way DAN

Denon Dn-X1500... | Answered on Dec 29, 2009

1 Answer

Power conversion

If you have 110 - 120 volts AC at 60Hz, then the mixer must be bad. Unless 50 Watts isn't enough. Does the voltage drop when you plug in the Mixer to the convertor?

Geno

Denon Dn-X1500... | Answered on Mar 05, 2008

0 Answers

I have a denon DCM-360 still working --but certain discs it does not recognize --these are CDs I just bought from amazon, still sealed (Dutton label).

Denon Audio... | Posted 3 days ago | Be the first to answer

0 Answers

Avr 1600RD. How can I reset?

Denon Audio... | Posted on Jan 16, 2021 | Be the first to answer

1 Answer

I have a Denon AVR-3200G Amplifier. There is no sound from the center speaker and the Subwofer.

Check the speaker wires and connections.

Denon Audio... | Answered on Jan 04, 2021

1 Answer

My Denon DRR 6.5 has suddenly stopped working, is there any way I can fix this myself?

SAD TO SAY BUT UNLESS YOU HAVE TRAINING IN ELECTRONICS I DOUBT YOU CAN FIX IT

Denon Audio... | Answered on Nov 14, 2020

1 Answer

I can't get my Denon dra 37 receiver to power on.. absolutely no power.. what do I do?

- check power cord
- check main fuse

https://www.manualslib.com/manual/910410/Denon-Dra-397.html?page=1#manual

Denon Audio... | Answered on Nov 14, 2020

1 Answer

How to reset denon AVR-X2300W ?

Power off using the power button and press together TUNER PRESET CH + and TUNER PRESET CH. Remove fingers when Initialized appears on the screen. It will reset the Denon AVR-X2300W.

Denon Audio... | Answered on Nov 09, 2020

3 Answers

Mcs 160 subwoofer no power

I had the same problem with my subwoofer unit. I found the zener diode ZD3 was fried. The pic below shows the diode and its clearly tagged ZD3. You need a multimeter to check this before you order anything. This diode should only transmit power in one direction. Its size and spec is 18v .5w zener diode. (that's 1/2 w) It's very inexpensive and the whole repair took about an hour. This is from a Boston Acoustics subwoofer MCS 160
Ok..the procedure is easy.
1) unplug the unit and bring it to a well lit work area.
2) remove the panel from the back and locate the board that is held to the panel by 4 screws and has the ZD3 diode. The pic below shows the diode at the end of my test lead. Note the direction of this part and reinstall the new one in the same direction. Its a simple de-solder and re-solder project. I elevated the new diode about 1/8 " from the board with a small strip of copper. This acted as a heat sink during the soldering and elevated the part above the board to help it dissipate heat later when in use.
3) re-install the board and plug in all the connections.
4) this worked for me and I'm enjoying my sound system again!..good luck

Denon Audio... | Answered on Sep 23, 2020

1 Answer

How do I connect my blue ray DVD player to the Denon AVR-1705-685 receiver?

This will depend on the Blue ray player and other equipment. For a direct connection to the receiver, if your player has either type of digital audio output (coaxial or optical), get the appropriate cables. Then connect the chosen cable between the Blue ray player and the receiver. Connect the Blue ray player to the TV with an HDMI cable. See page 10 of the manual, available at http://pdfstream.manualsonline.com/6/69f43064-f593-49b8-8d4a-23174b496e65.pdf , to see the connections for the audio sources. (I'll assume your Blue ray player doesn't have component video out or you would use the component audio to the receiver.)

If your player doesn't have a digital audio output, check your TV audio output. You can get the same result by sending the videos via HDMI to the TV and using the TV audio out to the receiver. Set the audio source to TV and leave it there for both TV and Blue ray and DVD videos. (Sometimes there could be a slight delay in the audio compared with the video signal when you do this. I've never noticed it with my Blue ray player signal going to the TV and the TV digital audio out to the Denon receiver.)

If you can't send the audio out to the receiver from either your Blue ray player or TV, then you will need some sort of HDMI audio extractor. You can find models with Analog Audio Out, Digital Audio Out or both. ( https://www.amazon.com/J-Tech-Digital-Extractor-Converter-JTDAT5CH/dp/B00BIQER0E lists units with both types of audio output. One models requires a 3.5 mm to RCA audio adapter.)

I hope this helps.

Cindy Wells

Denon Audio... | Answered on Aug 08, 2020

1 Answer

How do I set the

After you have set your clock time simply just hold down memo button and I goes to minutes and click memo once to save your chosen time.

Denon Audio... | Answered on Apr 29, 2020

1 Answer

My Denon DRA-395 Receiver, suddenly stopped working after I had a huge power (sound) surge for a moment. I immediately turned the sound down, but it seems like I may have shorted something out.

I expect your tuner/amp has a fair number of ultra sensitive CMOS devices inside and a power surge is likely to be instant ***** for them - if the surge reached them.

Any piece of equipment that has a computer inside really should be protected by an anti-surge device.

Your Denon tuner/amp is a bit of really premium equipment and I advise you it is best to entrust it's resurrection to a Denon approved repairer.

Denon Audio... | Answered on Apr 26, 2020