20 Most Recent Fisher and Paykel 24 in. DD-602 Built-in Dishwasher Questions & Answers


Fisher paykel dd603 - both drawer units just come

There is water collected at the base of the dishwasher which is tripping flood switch. Will need to disconnect power and take the bottom drawer out and dry out the base. Need to find source of the leak. Most likely the lid seal or hoses.
3/28/2022 8:12:50 PM • Fisher and... • Answered on Mar 28, 2022

Hello, I have a Fisher

Hello,It sounds like the dishwasher is in flood mode. You would need to dry up the water in the base pan and test. The link below is a video that explains how to repair your fisher paykel dishwasher.Fisher Paykel Dishwasher Repair Video
2/25/2015 9:20:37 PM • Fisher and... • Answered on Feb 25, 2015

How do I test the actuator on the bottom drawer

There is a sequence of button presses explained here Fisher Paykel Dishwasher Servicing Fisher Paykel Dish Drawer Repair
6/22/2014 10:38:26 PM • Fisher and... • Answered on Jun 22, 2014

Red light U3

The U3 error code could mean a few things. Not sure if you get it in both or just one drawer.

It could mean there is something blocking the drain pump. Lift the filter plate and drain filter. Then remove the rotor by disengaging the collar holding the impeller and rotor assembly. clean the area including the channel between the rotor cavity and the drain sump. Put everything back and test.

If this does not get rid of the U3 then it is possible there is a kink in the drain hose. Pull the drawers out and check behind. If nothing visible then other possibility is the inlet water pressure setting is not correct. If you know how to read the water pressure setting from the display then compare the setting on the two drawers.

Please post a comment to let me know what you find.

6/16/2014 12:19:09 AM • Fisher and... • Answered on Jun 16, 2014

Temperature sensor location for DS601

There is no separate temperature sensor. Everything is part of the Heater assembly. Need to replace the lot. Not sure if you can buy one for DS601 anymore. seehttp://www.genuineapplianceparts.com/item/527700_Fisher_Paykel_Dishwasher_Heater_Plate_DS602_DD602/3271/p3c50m40 I think the heater part numbers for DS601 and 602 are same. Check your model number in this catalog.http://www.genuineapplianceparts.net/partmanuals/dd602_602.pdf
4/3/2014 7:47:02 AM • Fisher and... • Answered on Apr 03, 2014

Fisher & Paykel dishwasher model dd602 error code F4

Hi there,
It means your filter is dirty. Remove metal plate at bottom & scrub with a toothbrush. Clean arms as well.
Clean all around the door & pull out the lift out filter, scrub clean with a toothbrush.

1/16/2014 6:52:37 AM • Fisher and... • Answered on Jan 16, 2014

I have a dd603 double drawer by fisher and Paykel.

Here is a suggestion: First turn the breaker for the dishwasher off for a minute or so then turn it back on. This will reset the controls. After that you should be able to select the cycle you want. Now for information on top drawer acting crazy. I had problems with the top drawer on a model 603I, I found that the control board under the drawer cover (at the upper right corner) had a broken latch. This allowed the control board assembly to drop down at the right side which caused the electronic eyes at the side of the drawer to become misaligned. This was giving false information to the control board indicating that the drawer wasn't closed properly. My problem was fixed by securing the control board back in place making sure the electronic eyes were lined up properly. (Note: The electronic eyes I am referring to include two clear plastic tubes about an inch and a half long to the right of the control board. These tubes must be properly lined up with the led and photocell on the side of the control board) It sounds complicated but if you take the drawer cover off you will notice the control board alignment immediately. Its an easy fix if this is your problem. One way to fix it is to take a piece of string and tie the board back in place. (That's what I fixed mine with and it has worked like new ever since.) NOTE: MAKE SURE THE POWER IS TURNED OFF BEFORE YOU BEGIN THIS REPAIR! suggestion:
11/22/2013 8:21:17 AM • Fisher and... • Answered on Nov 22, 2013

No power, can't open drawers.

Turn power off and then back on
4/29/2013 12:55:57 AM • Fisher and... • Answered on Apr 29, 2013

U3 error

It is unclear which model number you have, but in general U3 fault would mean the pump cavity is blocked. It could be also linked to water pressure setting on dishwasher not set at correct level for your mains pressure.Refer manual on page 33
3/21/2013 10:44:04 PM • Fisher and... • Answered on Mar 21, 2013

Drawer wont shut

If it is one of the two drawers that will not shut, them most likely the lid seal is locked in close position or the lid seal is damaged and pieces of it are blocking the drawer.Try to shut the power to the dishwasher and take the power chord out from the socket. Then insert back and turn power on.See if this makes a difference. If not the lid actuator motor or the lid seal need to be replaced. Will need a technician if you are not familiar with repairs especially the dishwashers are very sophisticated and are sensitive to how one repairs it.
1/5/2013 6:07:41 AM • Fisher and... • Answered on Jan 05, 2013
Not finding what you are looking for?
Fisher and Paykel 24 in. DD-602 Built-in Dishwasher Logo

116 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dishwashers Experts

Brian Coughlan

Level 2 Expert

280 Answers


Level 3 Expert

85241 Answers

Paul Bade

Level 3 Expert

1777 Answers

Are you a Fisher and Paykel Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fisher and Paykel Dishwashers

  • Fisher and Paykel Dishwashers

Most Popular Question

no power open drawers

  • Dishwashers