20 Most Recent Fisher and Paykel 24 in. DS-603 Built-in Dishwasher Questions & Answers


It could have fogged up because you had the drawer cover off in the first place.

The problem may be the alignment of the mirrors. If the control board has slipped down so that the mirrors do not line up to the photo cell and led---that can cause the problem you are having. Make sure the mirrors (light tubes) are properly lined up with the photo cell and led on the control board. You may have to move the control board to make this alignment. Once aligned secure the board in place and this should solve your problem. NOTE: MAKE SURE THE POWER IS TURNED OFF BEFORE YOU MAKE THIS REPAIR.

Fisher and... | Answered on May 23, 2017


User Guides, Installations & Parts Manuals - Fisher & Paykel

https://www.fisherpaykel.com/nz/support/user-manuals/

Fisher & PaykelFind and Download User Guides and Installations Manuals for your Fisher & PaykelAppliances: ... This will help getting a quicker and more accurate result.

Expert Tips, Troubleshooting & FAQs - Fisher & Paykel ...

https://www.fisherpaykel.com/au/support/expert-tips/

Fisher & PaykelExpert Tips. Select a product type to see solutions to most common problems you may encounter with your appliance. Search. -Select-, Built In Ovens, Electric ...

[PDF]user guide DishDrawer Ph7 Eng - Fisher & Paykel

https://www.fisherpaykel.com/.../590199D%20DishDraw...

Fisher & Paykelguide', you can download it from our local website, listed on the back cover. Refer to ...Preference options and how to change their settings ... standard safety regulations.Fuse cover. Fuse. Electrical connection (GB IE only) ... Do not use an extension cord or a portable electrical outlet device (e.g. multi-socket outlet box).

[PDF]Controls (models with LCD) - Fisher & Paykel



Fisher and... | Answered on Dec 25, 2015


check the hose is not kinked that lets the waste water out. otherwise change the rotor at the bottom of the drawer. this can be accessed by unscrewing the panel at the bottom of the drawer to reveal the rotor. lift it out and place the new one in. replace the covers. try again.

Fisher and... | Answered on Dec 08, 2014


I found a ball bearing stuck in one of the draw runners ?

http://www.scribd.com/doc/6462163/DD601V2-Manual see if this link still works

Fisher and... | Answered on Oct 03, 2014


The flood switch is at base of dishwasher housing under the drawer. Water leakage has occured to trigger this. Turn power off to dishwasher and take the power chord out. Pull the drawer out and use towels and hair dryer to dry the base. Put drawer back in and reconnect. Should work. Need to find the cause of leak. Either damaged lid seal or leaky hoses. Sometimes too much foam in detergent can cause it. Use recommended detergent and appropriate quantity per user manual.

Fisher and... | Answered on Apr 22, 2014


Water flood in the base of dishwasher. Check the fault code lights. If F1 then this confirms the problem. Need to find the source of leak.

Fisher and... | Answered on Apr 12, 2014


The flood switch has turned on. There is a leak into the base of the housing. Turn mains power off. Open bottom drawer and dry the base using towels etc. Need to find the source of leak. Lid seal or hoses.

Fisher and... | Answered on Apr 03, 2014


It is also likely the drawer has come off the gliding rail at the right.

You will have to pull the drawer out from the housing and check. Not sure if you have a standalone unit or integrated with the kitchen cupboard. The instructions to pull drawer out are available in the installation manual. Select the correct model from this site .
http://www.fisherpaykel.com/au/support/user-manuals/

Fisher and... | Answered on Jan 19, 2014


Let's go to diagnostic test mode to see if you can retrieve the the actuator hence the tube out.
1- Press Lock button and start/pause key until the display showing up.
2- Press Power to show HO.
3- Press start button to advance the display until you see P2 for draining, if you pass, keep doing it to get it back in a loop.
4- When at P2, press lock to turn on, press a again to turn off.
5- Listen to the sound of the pump. If you hear nothing that means the pump is dead or stuck.
6- The Motor has 2 directions: one for, Rinse and one for Drain. When you done with the diagnostic, press the power button to get out of the mode.
7- If this is the case, unplug the power then remove the rack, the bottom stanless steel plate with holes then take out the rotor to clean up. It is a good design the stator is outside of the tube, so you don't have to worry too much about the complication.
8- Make a note of all the positions so you can put them back the same as they were. Good luck

Fisher and... | Answered on Apr 28, 2013


This can mean several things. If you have double drawer dishwasher then you need to confirm if you get the F1 message in both drawers or just one.
If both drawers then it is caused by water leakage and flood switch activiates. If only in one drawer then the power supply to the other drawer is blown.
For single unit drawer it means flood switch triggered.

Fisher and... | Answered on Jan 21, 2013

Not finding what you are looking for?
Fisher and Paykel 24 in. DS-603 Built-in Dishwasher Logo

85 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Paul Bade

Level 3 Expert

1666 Answers

Are you a Fisher and Paykel Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fisher and Paykel Dishwashers

  • Fisher and Paykel Dishwashers

Most Popular Question

dish drawer will not empty properly

  • Dishwashers
Loading...