20 Most Recent Hoover Nextra HNF 2137 Front Load Washer - Page 3 Questions & Answers

Hi, you can close the door and test the machine first. If it does not work properly, then you can schedule an appointment with geeksquad bestbuy to repair the washing machine or replace it for you. Thank you.

Condenser dryers are simple in operation. They use a heater element to force hot air to heat the clothes and turn the water to steam. That steam is turned back into water by drawing cold air into the machine and over the heat exchanger unit and into the drum. The problems with them is that they are slow to dry. Your best bet is to call for service, and the problem is likely the sensor probe or one of the thermal cut out. https://www.4candy.co.uk/tumble-dryer/ro-h10a2tce-80-31101805/catalogue.pl?path=111515,111515&model_ref=14378839&page=2 ..

Here you are; https://www.youtube.com/watch?v=95HTHDp_ad0

if voltage to display board bad board

https://www.espares.co.uk/advice/careandmaintenance/how-to-fix-an-e13-error-on-a-hoover-washer-dryer

check belt if ok check under agitator for worn cogs

If error code E2 appears in your display there is a problem with the water supply. It may be that the water pressure is very low or no water is flowing in. Check that the water supply is switched on or that the hose has not got twisted or kinked during the installation which will prevent water flowing into the machine. An E2 Error code indicates that the washer is still draining after 8 minutes. Check the following: Check that the drain hose is not more than 391 ?3" (100 cm) from the floor. Remove any clogs from the drain hose.

Usually the bearing is a press fit as is the pulley.To be sure of not damaging it, contact a domestic appliance repair shop for assistance and you could get some idea of how to do it and the tools required but it will probably be cheaper to replace the machine.Don't forget, Hoover have a 10 year parts guarantee.

check belt if one and make sure motor turning

I would say check for a fuse blown. Not in your panel, but in the machine. These fuses could be bolt up or inline. But will always be accessible. Shine a light through it and it should make a solid and visible connection. If not, that's your culprit.

Very often the service guide and wiring diagram is hidden in the top console or in the upper part of the body stuck to the wall is a plastic bag. There might be a Service Manual, but you need the numerical model number rather than the fancy name '500'. https://www.google.com/search?q=hoover+500+washing+machine+service+manual ..

Too many clothes, not enough water, usually. However, this is a known issue on this Australian Washer. Throw it out, and buy a Front Loader. They take more laundry, use less water and electricity and don't tangle. https://www.google.com/search?q=HOOVER+500MB+WASHING+MACHINE+tangles+clothes ..

Turn it off at the mains. Leave it an hour and start again. Here is your manual in case you need it https://www.manua.ls/hoover/hn-6135/manual and even a 1 hour video :>)

Hoover Nextra HNWF6135 Washer Dryer - YouTube

https://www.youtube.com > watch 1:03:21 this is another of your choice! hoover nextra doing a cotton 40. please take a look at my amazon.

Crackling certainly doesn't sound good. How many days past warranty. Contact them, " 2 weeks ago my washing machine stopped working, I was going on a business trip, and couldn't do anything about it. I checked the fuse and it had blown. I replaced the fuse and it still doesn't work. When the machine failed it was in warranty, please come and fix". If not, the most likely issue for 'crackling' would be the control board or the motor, leaning slightly to the control board as it has no power visible to it. A failed motor would have power to the board, but nothing happening.

Faulty control panel

Possibly the control board is failed.

Easy peasy! Just fixed the same problem! Unplug machine..Take lid off machine.. Look behind program selected and unplug from circuit board (don't be scared! Try and unclick from inside the select know with small screwdriver then spray some contact cleaner in front hole and over the contacts to circuit board. It's ok.. Disolves and dries really quick.... I used the wd40 one me.. NOW NORMAL WD40!!) then put know back on and give it a good turn in both directions. Put all back together and problem should no longer exist.

COULD BE ANY NUMBER OF THINGS. CONTROL BOARD . MOTOR , TRANSMISSIN, CALL A LOCAL REPAIR SERVICE

I would suspect the transmission has gone out .but with out any testing no one can ever be sure

Error code E01 indicates a defective door latch or associated wiring or connection to control board.