20 Most Recent Hoover Nextra HNF 2137 Front Load Washer Questions & Answers


I had a problem and when they took the back off. Underwire bra had got jammed through drum holes which stopped it spinning and water issues. I hope this might help.

Hoover Nextra... • Answered on Aug 20, 2012


It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Check this link to replace the inlet valve:http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

Hoover Nextra... • Answered on Jul 03, 2012


Your door lock/latch is broken, this is a common issue with front loading washing machines and the only way to fix it is to replace the door switch.

Hoover Nextra... • Answered on Mar 05, 2012


a bearing is worn out or there is a clip that holds it in place that has worn out to

Hoover Nextra... • Answered on Jan 18, 2012


Hi from retired Englishman in SW France,

'....but did not drain them...'

I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter- so many 'faults' are caused by blocked filters.
Following are my complete and hopefully 'coverall' pre-typed guidance notes for checking both the drain motor filter and the drain motor ;-0)
REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Hoover Nextra... • Answered on Sep 24, 2011


the problem is simply when loading clothes u check the amount of water the machine can collect cos some machines don t take much water while washing or u call ur technician 2 come and check it

Hoover Nextra... • Answered on Jun 22, 2011


no power at machine is the fuse in plug ok. if ok switch off remove plug take off lid and just look at connections from mains cable are they ok and not burned then if ok look at the main pcb make sure connections are tight door switches on these machines were fairly trouble free so i can only advise you on the basics of fault finding with the limited info hope this helps

Hoover Nextra... • Answered on Jun 07, 2011


Hi


Thanks for using FixYa. The start and pre-wash usually flash due to a clogged drain hose or the water pump. You’ll need to drain the water out of the base and also check to see if there's something stuck inside the pump or the drain hose connected to the pump (pump is usually located at the bottom and towards the back of the washing machine). If the drain line isn't clogged, you may have a problem with the water pump such as a frozen pulley or a broken impeller. If that's the case replace the water pump. Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

Hoover Nextra... • Answered on Apr 10, 2011


yea its common its the pcb board you will find this behind the control panel if you remove the board you will see where it has blown sorry

Hoover Nextra... • Answered on Jan 18, 2011


Sony Ericssion
P990i what is the memory capacity ? how much GB is supported ?

Hoover Nextra... • Answered on Apr 30, 2010

Not finding what you are looking for?
Hoover Nextra HNF 2137 Front Load Washer Logo

51 questions posted

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Sheldon Dedek

Level 3 Expert

912 Answers

Mike

Level 3 Expert

4377 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hoover Washing Machines

  • Hoover Washing Machines

Most Popular Question

machine wont sart

  • Washing Machines
Loading...