20 Most Recent Hoover H120M Front Load Washer / Dryer Questions & Answers

0answers
0helpful
1answer

I have a front load Hoover washing machine. The two last times i've done the laundry the machine keeps adding water the entire time; it seems to be filling up and draining at the same time. It also st

My guess is the printed circuit control panel(the brain) is going south. There is nothing you can do with these normally, best to get a domestic appliance guy/gal to check it out. If you want to search the web for a replacement get to the back of the machine, write down the make/model/serial number/ anything else, off the manufacturers plate. You will need this to determine any spares are correct. Don't work on the basis that a similar machine or even the same model will have the same part because appliance manf are notorious for changing specs during production. You may find that another brand is listed as well as your own, this is because they have the same factory but are badged according to brand or region. If the machine is old and had a good beating then you may find it more economical to buy a new one. The brain can be 50% of a new buy!!
5/20/2014 9:40:05 AM • Hoover H120M... • Answered on May 20, 2014
0answers
0helpful
1answer

Washing mechine 1200 hoover

Hi, It sounds like it might need new brushes in the motor. Sometimes just before they wear down completely, they will wash but not spin, this is because the spin needs more power. Tom.
12/30/2012 1:21:24 PM • Hoover H120M... • Answered on Dec 30, 2012
0answers
0helpful
1answer

Door locking

the door mechanisum is proberly worn and the catch its best to replace both
12/6/2011 12:49:10 AM • Hoover H120M... • Answered on Dec 06, 2011
0helpful
3answers

Hoover washer dryer saver 1300

I have inherited a hoover saver 1300 in new flat, the dials have worn away and it goes onto drying mode after wash, how can i have it on wash and spin only - NO DRYING? Thanks
8/22/2011 3:29:15 PM • Hoover H120M... • Answered on Aug 22, 2011
0helpful
1answer

I WANT THE WIRING DIAGRAM

Hi from retired Englishman in SW France,

Sorry, this forum is not able to supply any type of manual, installation instructions, electrical or schematic diagrams direct; it's just made up of ordinary guys and gals, probably at home and from all over the world, with experience of addressing problems and giving guidance for free on the web ;-0)
Also members on Fixya are not 'affiliated' to, or representative of, any manufacturer at all, just using their experience gained probably over many years.

You will need to type into your search engine/web browser '(make model number) washer technical manual' and you MAY be presented with a number of sources from which you can either download for free or have to pay a nominal amount.
You could also try the manufacturer's web site direct but they often only supply to their registered engineers ;-0(

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.
7/10/2011 10:00:12 AM • Hoover H120M... • Answered on Jul 10, 2011
0helpful
1answer

Hoover WDM120 scraping noise heard

have come across this prob before the noise you describe sounds like an underwire from a bra or the condencer on the back of the mach some had a baffle plate fitted just where it goes onto the backof your mach on some this came loose and caused it to scrape of the back of the drum hope this helps .
6/7/2011 6:31:04 PM • Hoover H120M... • Answered on Jun 07, 2011
0helpful
1answer

The washine machine is performing

http://service.hoover.co.uk/manuals/pdfs/WDM120.pdf

This could be a problem in the pump or in the timer circuit, but since you say that it cycles normally I would guess that the drain pump has went out on this unit.
6/5/2011 1:32:51 PM • Hoover H120M... • Answered on Jun 05, 2011
0helpful
1answer

My washing machine is really loud when spinning

Hi from retired Englishman in SW France,
It is necessary to ensure absolutely that the machine has all 4 feet very firmly on the floor, and I mean firmly ;-0)
Doesn't matter whether it is empty or not but switch it off then-
very firmly push one front corner diagonally into the centre of the machine and see if the machine moves or rocks AT ALL, even the slightest. If it does you will need the open-ended spanner which came with the (new) machine........which of course went missing a long time ago?!! An adjustable spanner will suffice.
Adjust the foot under that corner downwards until it is very firmly- almost pushing- against the floor but not so far that the corner lifts up!
If this corner did not rock do the same to the other.
Once you cannot rock the machine the slightest little bit, screw the locking nuts up tight to the underside of the machine so that they will not move. Ideally the rear feet should also be locked.

(If this has not cured the problem it is possible that the internal suspension is malfunctioning).

If this has assisted you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C
4/13/2011 7:20:25 PM • Hoover H120M... • Answered on Apr 13, 2011
0helpful
1answer

There is a loud knocking when it reaches full spin

Hi from retired Englishman in SW France,

I DO suggest you follow my balance guidance notes right to the end before continuing the investigation ;-0)
------------------------------------
It is necessary to ensure absolutely that the machine, even when empty, has all 4 feet very firmly on the floor, and I mean firmly ;-0)

Doesn't matter whether it is empty or not but switch it off then-
very firmly push one front corner diagonally into the centre of the machine (sorry about my UK spelling!) and see if the machine moves or rocks AT ALL, even the slightest. If it does you will need the open-ended spanner which came with the (new) machine........which of course went missing a long time ago?!! An adjustable spanner will suffice.
Adjust the foot under that corner downwards until it is very firmly- almost pushing- against the floor but not so far that the corner lifts up!
If this corner did not rock do the same to the other.
Once you cannot rock the machine the slightest little bit, screw the locking nuts up tight to the underside of the machine so that they will not move. Ideally the rear feet should also be locked.

If this has not cured the problem it is possible that the internal drum suspension is malfunctioning.

Good luck,

John C
3/4/2011 8:38:46 PM • Hoover H120M... • Answered on Mar 04, 2011
0answers
0helpful
1answer

Hoover Washer/Dryer WM120 : Dryer function - drum not turning

Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor goingbad...

Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101



treru
9/30/2010 12:17:13 AM • Hoover H120M... • Answered on Sep 30, 2010
Not finding what you are looking for?
Hoover H120M Front Load Washer / Dryer Logo

68 questions posted

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

W.L.

Level 3 Expert

2511 Answers

Steve F

Level 3 Expert

1361 Answers

Mike

Level 3 Expert

4383 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hoover Washing Machines

  • Hoover Washing Machines

Most Popular Question

hoover washer dryer saver 1300

  • Washing Machines
Loading...