20 Most Recent Hoover Elite U5061-900 Bagged Upright Vacuum - Page 4 Questions & Answers

At the review page link, someone has had same problem with filter, etc coming off.

https://www.productreview.com.au/listings/hoover-heritage-5011
Excerpt:
the filter falls out on one of the wheels every time I use it, and the head section either falls out while you're using it, or it's so tight you can't separate it to put it away."

Seems this discontinued model falls into category of something works till it doesn't,

there are good and bad reviews on the 5011

Maybe a Jerry rig with color or eye pleasing quality duct tape (a dog eared tab is a much used fix) or reusable cable tie, has knots/balls that slide into a notch, Mouser electronics, or a 10 to 14 gauge insulated wire or modern equivalent twist tie.

If liquid is leaking from your Hoover Wind Tunnel Mach 6.9 vacuum cleaner, it could be due to a few different issues. Here are some possible causes and solutions:

1. Blockage: A blockage in the vacuum's hose or air passages can cause liquid to build up and leak out. Check the hose and air passages for any debris or blockages and remove them if necessary.
2. Damaged seal: The seal on the vacuum's dustbin or canister may be damaged, causing liquid to leak out. Inspect the seal for any damage or wear and replace it if necessary.
3. Clogged filter: A clogged filter can cause liquid to build up and leak out. Clean or replace the filter if it is dirty or clogged.
4. Faulty motor: If the vacuum's motor is faulty, it can cause liquid to leak out. Have the motor inspected by a professional and replace it if necessary.
5. Leak in the tank: If the vacuum has a tank, check if there is any leak or crack on it. If the tank is leaking, it needs to be replaced.

If your Hoover Power Scrub has suddenly become very loud, it could be due to a problem with the brush roll, the belt, or the motor. Here are a few things you can try to troubleshoot the problem:

1. Check the brush roll to make sure it is not clogged with debris or tangled with hair. If the brush roll is clogged or tangled, it can cause the vacuum to become loud.
2. Check the belt to make sure it is not broken or worn. If the belt is broken or worn, it can cause the vacuum to become loud.
3. Check the motor to make sure it is functioning properly. If the motor is not working, it can cause the vacuum to become loud.
4. If the problem persists after trying these troubleshooting steps, you may need to take the vacuum to a repair center for further diagnosis and repair.

I hope this information is helpful! Let me know if you have any other questions.

If the brushes on your Hoover model #5899-100 are not turning, it could be due to a problem with the belt, the brush roll, or the motor. Here are a few things you can try to troubleshoot the problem:

1. Check the belt to make sure it is not broken or worn. If the belt is broken or worn, it will need to be replaced.
2. Check the brush roll to make sure it is not clogged with debris or tangled with hair. If the brush roll is clogged or tangled, it will need to be cleaned or replaced.
3. Check the motor to make sure it is functioning properly. If the motor is not working, it will need to be repaired or replaced.
4. If the problem persists after trying these troubleshooting steps, you may need to take the vacuum to a repair center for further diagnosis and repair.

It sounds like there may be a problem with the charging system on your Linx charger. Here are some troubleshooting steps you can try:

1. Check the charging cable: Make sure that the charging cable is properly plugged into the charger and the device being charged. Check for any visible damage or fraying on the cable. If the cable is damaged, it will need to be replaced.
2. Check the charging port: Make sure that the charging port on the device being charged is clean and free of any debris. If the port is dirty or obstructed, it can prevent the device from charging properly.
3. Check the battery: If the device being charged has a removable battery, make sure that the battery is properly installed and not damaged. If the battery is damaged or not properly installed, it can prevent the device from charging.
4. Check the power source: Make sure that the power source, such as an outlet or power strip, is functioning properly and is providing an adequate power supply.

If these troubleshooting steps do not resolve the issue, it is possible that there is a problem with the charger or the device being charged. In this case, it may be necessary to have the charger or device repaired or serviced by a professional.

To clean the brushes on a Hoover SteamVac without breaking anything, follow these steps:

1. Turn off the SteamVac and unplug it from the electrical outlet.
2. Locate the brushes: they are usually located under the unit near the front or in the back.
3. Remove any debris or foreign objects from around the brushes.
4. Use a small brush or toothbrush to gently clean the brushes of any dirt or debris. Be careful not to bend or break the brushes.
5. Replace the brushes and reassemble the SteamVac.
6. Plug the SteamVac back in and turn it on to test if it is working properly.

If the brushes are damaged or worn out, they may need to be replaced. It is also a good idea to refer to the owner's manual for specific instructions on how to clean and maintain the brushes on your model of Hoover SteamVac.

Question edited for clarity. Question moved from Televisions category. All about blinking lights on Dyson and Hoover. Either the charger has failed or the battery has failed. https://www.google.com/search?q=Hoover+Blade+Stick+Vacuum.+I+don%27t+have+blinking+blue+light ..

START with this YOUTUBE Video! While it's NOT your specific HOOVER model ~ the steps WILL help you! Hoover SteamVac brushes not spinning For PARTS see this link to ID them: Hoover F7458900 Max Extract Carpet and Hard Floor Cleaner Parts Anthony

It needs FULL make and model, but there are videos and parts. https://www.google.com/search?q=hoover+vacuum+switch+replacement ..

some reasons switch --pump failure---hose nozzle clogged

First of all there are no propellers in any dirt cup of a vacuum cleaner. Some of them use a cyclonic action to keep the dirt in a ball shape for easy empty purposes. As the cup fills, it’s less likely to spin. Regardless, the spinning action has little to do with suction power. Clean the squirrel cage fins and filter would help.

try to unstick trigger if ok spray motor stuck on

There are no belts lol. Its a carpet shampooer

all the parts are here https://www.ereplacementparts.com/hoover-fh50220-max-extract-pressure-pro-parts-c-37315_37419_139660.html BUT, there are many models and you haven't supplied the model number https://www.partswarehouse.com/Hoover-SteamVac-Max-Extract-Series-Parts-s/5922.htm ..

Try a couple of wraps of good quality duct tape.

I have a Hoover smartwash that I've had for about a year. Recently it's been having trouble dispensing water. I've tried unplugging it and plugging it back in, but that doesn't seem to work. I've also tried turning it off and on again, but that hasn't worked either. I'm not sure what to do because I don't want to have to buy a new one already.

check for clogged nozzle

This is common. You need to remove the brush roller completely and untangle hair and threads from around the spindle. The roller should turn very freely. Yours isn't and is causing the drive belt to slip and create the smell.