20 Most Recent Rancilio Rocky Espresso Coffee Grinder - Doser - Page 9 Questions & Answers

If your magic wand is not vibrating anymore, there might be a few potential reasons for this:

1. Battery: The battery may be dead or running low. Try charging or replacing the battery to see if this solves the issue.
2. Motor: The motor in the wand may be worn out or damaged, preventing it from vibrating. This can happen over time with frequent use.
3. Wiring: There may be an issue with the wiring inside the wand that is preventing it from vibrating.

As for the light still working, it is possible that the light and vibration functions of the wand are controlled by different components. If you are unable to determine the cause of the issue, it may be best to contact the manufacturer or a professional repair service for assistance.

If your descale light is still on after descaling your coffee maker or espresso machine and performing a power off and reset, there are a few things you can try:

1. Double-check that you followed the descaling instructions correctly. Make sure that you used the right amount of descaling solution and water and that you let the machine complete the entire descaling cycle.
2. Try unplugging the machine from the power source and letting it sit for several hours. This can sometimes reset the descale light.
3. Check the user manual for your machine to see if there is a specific way to reset the descale light. Some machines require you to hold down certain buttons or perform a specific sequence of button presses to reset the light.
4. If none of the above steps work, there may be an issue with the machine's sensors or circuitry. In this case, it may be best to contact the manufacturer for further assistance or to have the machine serviced.

If the hot water spout and steam wand are functioning normally, but there is no water coming out of the coffee spouts during the rinse cycle, it is likely that there is a blockage in the water pathway leading to the brew unit. Here are some possible causes and solutions:

1. Water filter: If your machine has a water filter, check to see if it needs to be replaced or cleaned.
2. Water tank: Check the water tank to make sure it is properly seated and that the water level is sufficient.
3. Water pathway: The water pathway from the tank to the brew unit may be blocked with scale or debris. Try running a cleaning solution through the machine to clear the pathway.
4. Brew unit: If the above solutions do not work, the problem may be with the brew unit itself. Check to see if it is properly seated and clean. If it is damaged or worn, it may need to be replaced.

If the problem persists, it may be necessary to have a professional technician inspect and repair the machine.

It sounds like there may be a blockage in the coffee delivery system of your Carezza. Here are some steps you can take to troubleshoot the issue:

1. Check the filter basket: Make sure the filter basket is clean and clear of any coffee grounds or debris that could be causing a blockage.
2. Clean the group head: Remove the group head and clean it thoroughly with a brush and hot water. Pay special attention to the holes where the water comes out.
3. Check the water tank: Make sure the water tank is full and properly seated in the machine. If the water tank is not seated properly, it can cause low water pressure.
4. Descale the machine: Over time, mineral deposits can build up in the machine and cause blockages. Descaling the machine can help remove these deposits and improve water flow.

If these steps do not resolve the issue, it may be necessary to disassemble the machine to check for more serious blockages. If you are not comfortable doing this yourself, it is recommended to take the machine to a professional for repair.

It sounds like there may be a blockage in the brewing unit or the drainage system causing the water and coffee grounds to back up and overflow into the grounds container. You can try cleaning the brewing unit by removing it from the machine and rinsing it with hot water. Be sure to clean all the nozzles and crevices to ensure there is no blockage. You should also check the drainage system for any clogs or obstructions, such as coffee grounds or debris. This can be done by removing the drip tray and examining the drainage hole at the bottom of the machine. If these steps do not resolve the issue, it may be necessary to contact a professional for repair or servicing of the machine.

These machines are nothing but trouble! Try disconnecting from the mains for 10 minutes.

AppiaII-Manual-2-3Gr.pdf - Nuova Simonelli

https://simonelliusa.com > images > AppiaII-Manu... PDF of the group 2 or 3 for at least 8 seconds until the keys stop flashing. If you hold down the key of the second group, after first entering the programming.

• ProgramVip-Manual-All.pdf - Nuova Simonelli

  https://simonelliusa.com > images > ProgramVip-... PDF ENTER confirms this setting and passes on to the cup warmer stop time setting, which is carried out using the wv keys once the display has begun to flash. To ...

Top 8 Troubleshooting of Nuova Simonelli Espresso Machine

https://kitchensmom.com > nuova-simonelli-espresso-m... Troubleshooting 1 - Stop Light Remain On All The Time? Troubleshooting 2 - Is The Touchpad Flashing Unwantedly? Troubleshooting 3 - Is Nuova Simonelli Inept To ...

Troubleshooting NS Appia II - CoffeeSnobs

https://coffeesnobs.com.au > forum > equipment > 467... May 27, 2017 - Power off / on. Pump runs and then goes to a diag mode of sorts. That is... all lights on and flashing manual/stop on each group

Unfortunately, there is no user manual available for the Crofton TI-CM-1013 Coffee Maker with Thermo Jug. However, it is possible that the warmer plate can be switched on by pressing the "on/off" button. If this does not work, then it is likely that the warmer plate is not functioning properly and may need to be replaced.

When all the lights on your Jura Impressa C5 are flashing, it typically means that the machine is experiencing a malfunction or error. Here are a few steps you can try to troubleshoot the issue:

1. Turn off the machine and unplug it from the power source for a few minutes, then plug it back in and turn it on again. This can sometimes reset the machine and clear the error.
2. Check the water tank and make sure it is filled to the appropriate level. If the water tank is empty or low, the machine may not be able to function properly.
3. Check to see if the brew group is properly seated in the machine. If the brew group is not properly seated, the machine may not be able to start a brewing cycle.

If none of these steps work, it's possible that there is a more serious issue with the machine that may require professional repair. In that case, you may want to contact Jura customer service or a professional appliance repair service for further assistance.

1. Fill the water tank: Fill the water tank with cold water and make sure the tank is securely in place.2. Load the coffee beans: Open the top lid and fill the funnel with coffee beans of your choice.3. Select the desired program: Use the selection buttons on the front panel to choose the desired program.4. Start the machine: Press the Start/Stop button to start the machine.5. Wait for the desired coffee: The machine will grind the beans and dispense the desired coffee in a few seconds.6. Empty the grounds container: Remove the grounds container and empty it.7. Rinse the components: Rinse the funnel and the other components with hot water after each use.

No, don't worry, it may be the coffee. If it gets very wet, then yes it needs attention to the seals in the brew head.

I need the manual for Lumina Dutch Pancake Maker 36019

I need to find a thermostat for salad master 6 to 10 cupsperculator. Have any idea where I an purchase one.

If the motor gets hot on your grinder, check the carbon brushes, bearings, armature, field, fan, holder, and gears You bought a used item What discs are you using, they may be too thick, try a .040 or thinner. grinding disc it you are using tool to cut.

This machine turns up on Fixya often because of its problems. Take it in for service, as you have a very odd fault. Sounds like a faulty relay. https://www.google.com/search?q=simonelli+appia+problems+and+solutions ..

Switch machine off and back on. The water didn't hit the sensor fast enough. The machine does not detect the water flow in the circuit The water circuit is interrupted The alarm can be reset by switching the machine off Service Manual Page 37 refers. https://wiki.wholelattelove.com/images/3/3f/BLUE_2312_Service_Manual.pdf ..

The problem you are describing with your Magnifica S coffee machine, where it doesn't put out water when you turn it on to rinse, but sometimes outputs the coffee and other times just dumps it out into the tray, could be caused by a few different issues. Here are a few things you can check:

1. Check the water tank: Make sure that the water tank is properly filled and that the water level is high enough for the machine to function properly.
2. Check the water pump: Make sure that the water pump is functioning properly and that it is not blocked or clogged.
3. Check the water lines and hoses: Make sure that the water lines and hoses are not clogged or blocked.
4. Check the machine's settings: Make sure that the machine's settings are correctly configured.
5. Check the machine's firmware: Make sure that your machine's firmware is up to date and that there is no error.
6. Check the machine's grinder: Make sure that the grinder is not clogged and that the grind setting is set correctly for your beans.

If none of these steps resolve the issue, I would recommend contacting the manufacturer or a professional repair service for further assistance. They may be able to provide additional troubleshooting steps or may recommend a qualified technician to repair the unit.

If you are having trouble separating the bulk salt or pepper container from the motor base on your Trudeau Graviti mill, there are a few things you can try to fix the problem:

1. Make sure that the mill is unplugged and not in use.
2. Carefully pull down the motor base from the container and rotate it counterclockwise as the instructions indicate.
3. If the parts are still stuck together, make sure that the square shaft is properly aligned with the base. Sometimes the square shaft can become misaligned, preventing the parts from separating.
4. Check the square shaft to ensure that it is not bent or damaged in any way. If the shaft is bent or damaged, it may not be able to rotate properly and the parts will not separate.
5. Check for any debris or food particles that may be lodged in the connection between the container and the motor base. Clean the parts with a dry cloth and make sure that they are free of debris.
6. If the issue still persists, you may want to consult the user manual for your mill. The manual should have specific instructions for separating the parts.
7. If you do not have a manual, you may be able to find one online by searching for the model number of your mill.
8. If you are still unable to separate the parts, you may need to contact the manufacturer customer service or a technician for assistance.

The problem you're describing with your Pasquini Livia 90 Automatic Espresso machine cutting out and the lights flashing after reaching the proper temperature could be caused by a number of issues. Here are a few steps you can try to troubleshoot the issue:

1. Check the temperature sensor and ensure it is properly connected and functioning correctly. Make sure it is not blocked or damaged.
2. Check the thermostat and ensure it is properly calibrated and not damaged.
3. Check the heating element and ensure it is not damaged or malfunctioning.
4. Check the water pressure and ensure it is not too low or too high.
5. Check for any blockages in the water or steam lines and clear them if necessary.
6. Check for any clogs in the group head and clean it if necessary.
7. If the above steps do not resolve the issue, it may be necessary to have the machine serviced by a professional technician.

It sounds like you are experiencing an issue with the secondary boiler on your Saeco Vienna Deluxe coffee machine. In order to test the secondary boiler, you will need to follow these steps:

1. Remove the water tank and the brew group from the machine.
2. Locate the secondary boiler. It is usually located in the back of the machine and is a small, cylindrical shape.
3. Check the thermostat: Use an ohmmeter to check the resistance of the thermostat switch. If it is closed, the resistance should be very low (around 0 Ohm), if not, it could be the reason for the failure.
4. Check the thermal fuse: Check the resistance of the thermal fuse with an ohmmeter. If the fuse is open, it will have a very high resistance (infinity)
5. Check the heating element: Use the ohmmeter to check the resistance of the heating element. It should measure between 12-15 Ohms. If the resistance is outside of this range, the heating element may be faulty and will need to be replaced.
6. Check the wiring: Check that all the wiring is properly connected, and that there is no damage or loose connections.
7. Reassemble the machine: Once you have finished testing the components, reassemble the machine.

It's worth noting that if you are not familiar with the process of testing the components or if you find that the problem is more complex, I would recommend contacting a qualified technician or the manufacturer for further assistance. They will be able to diagnose and repair the issue with your coffee machine, and they can also give you an estimate of the cost of repair. It's also worth mentioning that you should not test voltages of live unit out of its case, as it is dangerous and could cause damage to the machine or injury to yourself.

Sounds like the motor underneath the frother unit has broken down. If you still have warranty, then go to the retailer. Otherwise you maybe can check the unit by opening it from the bottom and checking all the resistances of all the components with a multimeter to figure out what went down.