20 Most Recent Hotpoint First Edition FEW12 Front Load Washer - Page 9 Questions & Answers

We don't send anything. We aren't Hotpoint, and everything on Fixya is done online. The wiring diagram for that model is not online and neither is a wiring diagram. Head over to JustAnswer.com They have techs with secret access to files. https://www.google.com/search?q=Hotpoint+Aquarius+TVM+570+service+manual https://www.google.com/search?q=Hotpoint+Aquarius+TVM+570+wiring+diagram&tbm=isch&ved=2ahUKEwiZk_CU6vD1AhU9EFkFHf8mBCEQ2-cCegQIABAA&oq=Hotpoint+Aquarius+TVM+570+wiring+diagram&gs_lcp=CgNpbWcQA1C6FVjMRGDvSmgAcAB4AIABbIgB-QeSAQM4LjOYAQCgAQGqAQtnd3Mtd2l6LWltZ8ABAQ&sclient=img&ei=6cICYtn6EL2g5NoP_82QiAI&rlz=1C1QJDB_enCA643CA644 ..

Question edited for clarity. Question moved from Cars and Trucks Category. Call for service. You have and undocumented issue. https://www.google.com/search?q=hotpoint+g157+washer+clicking+noise and https://www.google.com/search?q=hotpoint+g157+washer+won%27t+shift+between+normal+and+gentle ..

there must be something wrong with the computer board, I would try getting some one else to have a look at it,if its triping the braker on the fuse board it must be the washing machine

possible didnt drain and caught in cycle or bad timer

try google or call tech support

check wireing harness

That sounds like an overheating problem. When the machine pauses, the blower fan stops running and that allows the heat to build up enough to trip the high level thermostat. You can test this by running a cool cycle. Drive belts don't squeak because they are made of rubber. Things that do squeak are rear drum bearing, front bearings or drum slides, idler pulley wheels or the tension springs. The machine needs a full strip down, cleaning, de-fluffing and lubrication. Also check the exhaust hose and the grill outside except it appears you have a condensing dryer. Make sure that unit is clean.. https://www.manua.ls/hotpoint/aqcf-852-b-i/manual?p=3 ..

https://www.espares.co.uk/search/ma808pt1553/washing-machines/bearings/hotpoint

Hi there,

F08 indicates "Heater Relay stuck or Pressure Switch stuck on full".
You'll need a multimeter to be able to carry out some checks.
Check the heater for continuity, you should get a reading of around 25 ohms.
Check the pressure switch connections on the main pcb, usually J3
Check the pressure switch wiring and connections.
Chek the wiring at the heater for internal breaks. (The wire looks ok but when pulled snaps easily).
Check the pressure tube and chamber.
Unplug the appliance from the wall socket.
Take the lid off and locate the pressure switch.
Take off the thin tube attached to it and blow down the tube to try and clear any restrictions in the pressure hose or chamber.
Refit the tube and try the machine again.
If everything checks out ok, it would suggest that the main pcb will require replacing and the software written to it.

Thanks

Remove the drain hose and lower it into a bucket. It has to be lower than the water level and pump.

The problem is most likely internal. You can try disassembling your machine up to the point where the technician will be a welcome sight. Check out some YouTube videos to see what you are letting yourself in for.

REPLACE IT WITH A CONVENTIONAL TYPE

call a local repair service

Could be traceable to a failing pump

circuit--valve-power failure use a meter to test components

You need a technician for issues like that. Overheating is dangerous. Yikes, there is a RECALL on that model!!

Whirlpool tumble dryer recall: full list of Hotpoint models being ...

https://inews.co.uk > news > consumer > whirlpool-reca...

Nov. 2, 2019 - Whirlpool recall: full list of Hotpoint tumble dryer models recalled - and how to get a free replacement. Whirlpool admitted as many as 800,000 ... https://www.hotpointservice.co.uk/safety-notice ..

Water spill om the motor I expect. Dry it out thoroughly and it may work again.

possible transformer shorted thats whats popping breaker

I thought it was probably a 'brushless motor', but they sell them for that model. They are funky, this is what they look like. https://www.ebay.co.uk/itm/HOTPOINT-WMAL641-washing-machine-motor-carbon-brushes-Connection-terminal-6-4m-/233628113721 VIDEOS on changing them https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk00kSRxldnKJ82uHf7utud8M6EGvMg%3A1612566982903&ei=xtEdYIjYNsfj_Aayo77ABw&q=hotpoint+aquarius+wmal641+replace+brushes ..

Hi,There are basically just few reasons :1. Maybe the water pressure is too low2. Hoses are blocked - check that there are no kinks in the cold water fill hose and the waste water hose too3. Clogged inlet valve - the water inlet valve supplies hot and cold water.You can read more about most common washing machine faults here - https://www.justfixed.co.uk/washing-machine-problems/