20 Most Recent Hotpoint Aquarius WF210 Front Load Washer - Page 3 Questions & Answers

sounds like ur pump is getting weak and going out it will have to be replaced

Make sure there is no water left in washer, and try door again.
If it still will not open,then remove top cover, and force door lock open from inside at the front.
You will possibly damage the door lock by doing this, but i am afraid there is no other way of doing it.

The filter is located at the bottom front of washer.
Remove the kickstrip at the bottom, by levering off.
Unscrew filter anti-clockwise to remove and clean..
Be careful when removing filter, as there will be water come out.Lay the drain hose down into a bowl or similar to drain off excess water.
Please rate my solution.
Thankyou

The filter is located at the rear of the washer.
Remove lower rear panel of washer.
Remove large black hose from bottom of drum.
Remove and clean filter inside hose
Remove hose onto pump, and check for blockage or obstruction here as well.
Please rate my solution.
Thankyou.

Undo screws at rear of top cover, push hard towards rear and lift at the same time to remove top.
Undo screws on lower rear panel to remove same.

In a word No

Click on the link below to download the user guide

http://imagebank.indesitcompany.co.uk/brochures_online/pdf/Hotpoint/Laundry/WFseries_19504110305_Jan05_book.pdf

Remove top cover, and lower rear cover of washer.
Get a hair dryer, and blow the hot air into the washer at every point you can gain access to.
If it still does not work, then it could be that one of the electrical components has suffered damage due to water getting on to it.
Good luck.

I am not a repair professional. I am a 78 year old man who has been making his own repairs for about 50 years. So the washer or dryer ID doesn't mean much to me. I came to fixya looking for a schematic for an really old AM/FM radio and found that more than 4,700 people were asking for help with a washer repair. I recently had a washer repair of my own and at that time I found an excellent video which showed me how to take my machine apart. This video made it possible for me to do my own repair. If you are repairing a dryer or a front load washer I suggest you
go to www.applianceaid.com where they have very good step by step trouble shooting and repair information on both washers and dryers as well as other appliances. If you have a direct drive top load washer and need help taking it apart this video is an early christmas present. I was so impressed with it that when I saw all these people needing help, I wanted to tell them about it. If you look at the back of your washer and the panel is solid (no small inspection plate to remove which would indicate you have a v-belt drive) chances are you have a direct drive and this video is just what you need. You can see it at www.acmehowto.com You will probably still need help in determining what the trouble is and how to fix it. After viewing the video or if you have a v-belt drive rather than a direct drive, I suggest you go to www.applianceaid.com where they have very good
trouble shooting and repair nformation on most
washers and dryers. I think you'll find what you need
there. Don't worry about the timer, they hardly ever
go bad. Good luck with it. If I have helped you, please rate my advice on fixya.

ck the pump for lint ect . and clean it out a slow drain problem could cause this . also a kink in drain hose .. hope this is helpful . mm

Check and clean the pump filter.
Remove lower rear panel of washer, remove large black hose on bottom of drum,remove and clean filter inside, alsr remove hose onto pump, and check for obstruction here and in the pump.
Please rate my solution.
Thanks.

Switch on the machine and presss the start/cancel button this should take the "test" off the display. Then press and hold both the start/cancel and on/off buttons for a few seconds. The display will show d off and then the waher will work as normal.

if your inner drum is loose
you have a broken spin assembly
a rather large repair

not to hard, take the bottom rear pannel off the washer, look at the bottom of the drum were the water drains out, look for an oval shaped plate with possibly 2 or 3 wires and possibly a small plug going to it remove these, loosen the centre nut that takes pressure off the seal and it will pull out. best of luck

hi
it may be the belt making noise,,,check it,,,

thank u,,,//////please rate it

I think the belt has come off or has been damaged.

To open the machine slide out the machine. On the back panel lower 1/3 you will see a plastic panel remove the screws and the panel will come away. Inside you will see the belt. I suspect you will need to reattach the belt of remove it and buy a replacement.

Sin é

Hi I think your problem is that the filter is blocked, filter is located between drum and pump at the rear, clean that out and that should solve the problem.

hi..Most washing machine have a drain filter that can become
clogged over time.Front load washers typically have a small
removable panel about the size of a half sheet of paper on the
bottom front of the machine.the filter is inside.
check it out..
thank u..
kindly rate my response..

Ironically I just had this happen. Pull the bottom panel off, remove the bottom two screws on the face plate and pull the latch release down (little white plastic Piece under the latch). This bypasses the electronic latch. To drain the washer, remove the plastic cover from the trap and the water will drain. Caution, this is very messy. Make sure you have a bucket and towels!

either the level control switch has become blocked or faulty or the drain pump has become stuck.

disconnect from the mains and gain access to the rear look for a circular unit with two or three electrical connections and a plastic tube. this is the level control.follow the tube to its start and you will find a plastic connection that goes into the wash drum, remove the plastic tube from the switch end and blow into it. if there is no restistance then the system is OK at the drum end. next reconnect the tube to the switch and remove the opposite end, very gently blow down the tube and you should hear the switch operate. Test wether the switch is working by putting a meter across the switch and blow into the tube. if all of this is OK then the drain pump is at fault. locate the drain pump. it is connected to the outlet tube, try turning by hand. if it does not rotate smoothly remove the clips holding the pump body together and clear the obstruction.

sorry not a answer as such. I found out the machine is still under guarantee. So I just called out the repair man.