Hotpoint Aquarius WF220 Front Load Washer - Answered Questions & Fixed issues

Could be the plug itself, or door interlock switch, try cutting off plug replacing Interlock cost is around 20GBP.

Hotpoint... | Answered on Oct 21, 2017 | 90 views

It does sound as if it is the switch, since you can eventually get it going. Depending upon the age of the washing machine, you will need to decide whether another repair bill is worth it. I would look at the last bill and call the repairman for an estimate of current charges if you are sure it is the same problem. I don't recommend attempting ANY repair by an unauthorized person to a major appliance. Good luck to you.

Hotpoint... | Answered on Jan 20, 2015 | 66 views

hi take top off door works on water presure normally clipped to side at top you will see a round or oval part with wires plugged in look at bottom of that there is a clear tube take it off by sqeezing clip pull off open door and put it back or else machine will just keep filling try back soap tray

Hotpoint... | Answered on Feb 17, 2014 | 30 views

check water pump filter, it may be blocked or jammed

Hotpoint... | Answered on Jun 03, 2013 | 354 views

Replace the bearings.... the only solution the machine will have a new lease on life.

Hotpoint... | Answered on May 28, 2013 | 22 views

undo door hinge from cabinet - held with two screws.
the door halves are held togethet with a few screws which undo and the door will split apart so you can replace the glass

Hotpoint... | Answered on May 22, 2013 | 154 views

Click this link: filter

Hotpoint... | Answered on Jan 25, 2013 | 20 views

sounds like the spider and drum bearing are on there way out

Hotpoint... | Answered on Sep 30, 2012 | 30 views

Hair clip stuck in pump remove pump then remove object

Hotpoint... | Answered on Mar 12, 2012 | 74 views

Things to do make sure despencer draw is clean and the rubber door seal is clean do a maintenance cycle every year this is the hottest wash cycle with cleaning detergent. also leaving the door open after cycle will help hope this helps

Hotpoint... | Answered on Jan 05, 2012 | 100 views

For the pump try taking filter back out and putting back again for smell clean out the rubber door seal with soapy water after the door seal is clean clean the despencer draw fully by taking it out. When you washed the seal and draw get washing machine clean for local super market and do a 95oc wash it should smell nice now if not could be drains hope this helps.

Hotpoint... | Answered on Jan 05, 2012 | 131 views

  • F07 - Heater relay stuck
  • This means your heating system has gone wrong you will need to book repair but you could try and reset machine turn off at plug for 5 mins and try again.
  • hope this helps

Hotpoint... | Answered on Jan 05, 2012 | 88 views this should help you fit a new door seal

Hotpoint... | Answered on Jan 05, 2012 | 432 views this should help you fit it

Hotpoint... | Answered on Jan 05, 2012 | 43 views

  • F04 - Pressure switch jammed on empty
  • This might need a repair you could try purring off machine at plug for 5 mins and switching back on if still does it you should book repair hope this helps

Hotpoint... | Answered on Jan 05, 2012 | 40 views

To check this watch this video and the set of videos about it hope this helps. it could also be the motor brushes wearing out hope this helps.

Hotpoint... | Answered on Jan 06, 2012 | 39 views

This is usually the door interlock wearing out, and not returning to normal quickly enough after spinning. Search on YOUTUBE for videos of how to replace one, it usually requires the door gasket to be un-clipped from the outer front panel area (behind the door). There are a lot of parts suppliers here if you need help: or HERE for a good video. Hope this helps, TD.

Hotpoint... | Answered on Oct 05, 2011 | 32 views

Please check the power to the mains controller unit and if present please check if the door switch is contacting to give the OK signal for the controller to start the function . So if the inlet does not open and allow water into then is seems that the program controller unit is a suspect.
recheck once again to confirm, try to swap a similar board to confirm and then replace.

Hotpoint... | Answered on Sep 13, 2011 | 160 views

Not finding what you are looking for?
Hotpoint Aquarius WF220 Front Load Washer Logo

202 questions posted

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

Eric Taylor

Level 3 Expert

590 Answers

Richard C Cohen
Richard C Cohen

Level 2 Expert

171 Answers

Onofrio Taverna
Onofrio Taverna

Level 1 Expert

12 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides