Hotpoint Ultima WF865 Front Load Washer - Page 9 - Answered Questions & Fixed issues


You will need to replace the washers electronic control panel.

Hotpoint Washing... | Answered on Jun 06, 2018 | 50 views


motor went out buy new one here. www.procellularservices.com just find the search engine type in the machine info if you want to get the same model

Hotpoint Washing... | Answered on May 07, 2018 | 89 views


Refer to your manual if you have one, if not, your machines filter may be full of lint or coins or other stuff. It is located at the bottom of your machine, just turn the nozzle and prepare for some water to escape, unscrew it, clean it all out and replace it, see if that helps... good luck

Hotpoint Washing... | Answered on May 03, 2018 | 30 views


AL01 is the error code for flooded base.
Firstly, disconnect the power cable!
Check the trumpet pipe that goes from the pump to the heater.
Is there water in the base, if so you need to remove the water and dry the base. Hope this helps and good luck.

Hotpoint Washing... | Answered on May 02, 2018 | 111 views


Request the assembly diagram directly from Hotpoint.

Hotpoint Washing... | Answered on Mar 20, 2018 | 30 views


Hi,
The empty tank & clean filter light will come after EVERY use of the machine,
because it is reminding you that this is what the user manual tells you that you're supposed to do EVERYTIME you use the machine.
If the machine breaks down because it's full of fluff, it may invalidate your warranty & a water tank with just a little water, is a lot easier to empty than a full one.!

Hotpoint Washing... | Answered on Mar 10, 2018 | 30 views


Hi,
F06 is a water level fault.
It will either be due to a faulty vacuum switch (which is the hockey-puck thing with the little tube to it,
or it will be not draining properly because of a blocked or faulty outlet pump or filter.
The worst case scenario is that it might be a control board failure.

Check the filter & pump first.
Check to see if the vacuum switch switches by sucking or blowing into the tube.
Sometimes just doing that can free it up if was stuck.?
Best of luck.

Hotpoint Washing... | Answered on Mar 09, 2018 | 172 views


Best Manuals Don't waste your money on unnecessary sources and unwanted repairs. Get this manual online under $10-15 and get complete guide on whether to repair or not, service it, and how to repair etc

Hotpoint Washing... | Answered on Mar 05, 2018 | 26 views


Hello!
First of all, make sure you have a machine witch is not with welded tub, a lot of these machines are made with sealed tub, so in this case you have a problem....
Check if it's with removable front panel, remove kickplate plastic down and chek for screws that hold front panel. If there are no screws and front is welded, it means you will need to remove tub upwards, which is a PITA. You need to remove all hoses, wires from motor, heater, sensors, unscrew shock absorber, remove detergent drawer from top, door gasket. and when everything disconnected, lift up the tub. Ask for some help because it's heavy.

Hotpoint Washing... | Answered on Feb 26, 2018 | 109 views


Is the outlet water pipe bent at all, in a way that would prevent the water from exiting? If not then I would confidently say that the pump has failed, if the machine has warrentee I would call hotpoint for an engineer visit... I hope this helps.....

Hotpoint Washing... | Answered on Feb 21, 2018 | 32 views


try the manufacturer's website .

Hotpoint Washing... | Answered on Feb 14, 2018 | 30 views


Please check for rodent nest. For some reason bugs and small rodents love to nest in areas of resistance..actuators..rexepticles..plug ins..sounds dangerous for the newborns right? Thing is its that old nest that is your problem now. It degrades and chunks jam here and there then stuff stops working. Adverse weather forces creatures to seek temperary shelter especially if a birthing event is looming. So don't try to stop it as nature always wins..but inspect your appliance as soon as you notice a change in performance before that nest costs you a days wages.

Hotpoint Washing... | Answered on Feb 09, 2018 | 75 views


Hi I hope the picture below helps, I can help you further with this as I have found that mine was a 5p blocking my pump fan at the bottom behind the lower front cover, I can talk you through how to do that, but it does involve unplugging the washer firstly, then using a sponge & bucket to remove as much water from the drum as possible & then tipping back machine & propping it up under with a strong solid object that can hold its weight for a while, but then slide a good solid tray under to catch the excess water & an old towel or rags near by for any splashes, then by undoing the front lower flap with a butter knife there are lugs about an inch in from each end, gently pop them down carefully & remove white cover, then by twisting the grey circle cap that is at the front of the pump fan, this can be hard to turn, but follow the arrows, I have had to turn mine using pliers before, turn this slowly because water will come out & it will be fast if you turn it to quickly soaking the floor, once removed look & see what is obstructing the pump fan blades, maybe a hair clip or a coin or limescale & hair etc, give it a good sweep around & rotate the fan blades & inspect closely with a torch to see any minor scratches or damage the fan, this may indicate the item is blocking something or if it's gone the other side of the fan or not, once this has been cleared & rotates & the filter if there is one has been cleaned & replaced back then reassemble it all together & then resit the machine, please leave & allow it to settle for a few mins to be sure that there is no leaks from the area you opened (sometimes a few drops as the water tipped backed wards will rush forwards & then it will be resealed, after a 5-10 min wait plug the washer back in, set it to the pump out & spin programme & this should clear the problem, it did with mine last summer... I hope this solves the problem..
I did add a picture from their website depicting what the error code is trying to indicate to you, but you probably have already looked for this already, Hope this helps....
2_8_2018_10_07_50_pm.png

Hotpoint Washing... | Answered on Feb 08, 2018 | 43 views


Check page 6:
http://docs.hotpoint.eu/_doc/19509812000_GB.pdf

CHILD LOCK button:
to activate the control panel lock,
press and hold the button for approximately 2 seconds.
When the symbol CHILD LOCK is illuminated,
the control panel is locked.
This means it is possible to prevent wash
cycles from being modified accidentally,
especially where there are children in the home.
To deactivate the control panel lock,
press and hold the button for approximately 2 seconds

Hotpoint Washing... | Answered on Feb 04, 2018 | 247 views

Not finding what you are looking for?
Hotpoint Ultima WF865 Front Load Washer Logo

139 questions posted

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

gbob59

Level 3 Expert

3063 Answers

Eric Taylor

Level 3 Expert

590 Answers

Richard C Cohen
Richard C Cohen

Level 2 Expert

171 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...