20 Most Recent Hotpoint Ultima WF865 Front Load Washer - Page 6 Questions & Answers

They melt due to high resistance across the solenoid and contacts. My only thought it that they were not genuine OEM replacements and were copies on eBay or Amazon and sourced in China. also follow the wires back to the control board and clean the contacts there. https://www.google.com/search?q=hotpoint+wml520+door+switch I can only find one other incidence of a door lock melting and it is here on Fixya. https://www.fixya.com/support/t29905283-ve_got_hotpoint_washing_machine_model https://www.google.com/search?q=hotpoint+wml520+door+switch+melting+problem ....

Typical Landlord comment. It is a totally electronic machine. They a power reset. Pull the mains plug when you go to bed, press and hold the power button as you plug it back it back in. Here is the manual if you need it. https://www.manualslib.com/manual/71052/Hotpoint-Wmf740-G-A-K.html ..

in front of door

I have a wdal8640, after a while the condenser pipe gets all fluffed up. Remove the lid, the cross bar and unscrew the metal heating unit. You're looking for the plastic tube that bends down the back of the machine. There's a ring holding it on at the bottom, once you've undone that and worked it over the prongs on the filter it should lift straight out. Give it a good rinse and remove any stuck lint (mine was a solid block that I had to break up before I could get it out), clear the filter whilst your in there and stick it all back together. Don't forget to reattach the water pipe to the top corner!!!

Based on the description, it seems that the control PCB module is a possible cause of the issue with your washing machine. Checking for any signs of burnout on the PCB would be a good next step. However, keep in mind that handling electronics can be dangerous and if you're not comfortable or familiar with the process, it's better to seek the help of a professional.

That sounds like you are on Pause or Delayed Start. Try Pressing and holding the button. You can also try disconnecting from the mains for 5 minutes. When in doubt, read the manual :>D START/PAUSE button with indicator light: starts or temporarily interrupts the wash cycles. N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the DOOR LOCKED indicator light is switched off, the door may be opened. To start the wash cycle from the point at which it was interrupted, press this button again. and also ! If the START/PAUSE indicator light (orange) flashes rapidly at the same time as the function indicator light, this indicates a problem has occurred (see "Troubleshooting"). https://manualzz.com/doc/50330217/hotpoint-fdl-9640p-uk-instruction-for-use ..

Yes it is a door lock issue. Check all the connections again and follow the wire back to the control board. https://www.google.com/search?q=fault+code+F6+on+a+Hotpoint+NSWM943CWUKN What does F6 mean on Hotpoint washing machine? F06 - Door lock fault. Issue: Washing Machines door cannot be opened or closed / when the door is closed the machine the programme will not start. Advice: If your washing machines door will not close, please check for any obstructions in the door lock.

Washing Machine Error Codes - Hotpoint Service

..

if the machine is old the front panel need to be service.Probably the front panel is experiencing partial contact with he control buttons.

If your Hotpoint FDEU 9640 washer-dryer is stopping prematurely during the dry cycle with all the LEDs flashing amber, it could be caused by a few different issues:

1. Check the filter: Make sure the filter is clean and not blocked. A blocked filter can cause the machine to stop working properly.
2. Check the venting: Make sure the venting system is clear and not blocked. A blocked vent can cause the machine to overheat and stop working.
3. Check the heating element: If the heating element is faulty, it can cause the machine to overheat and stop working.
4. Check the thermostat: If the thermostat is faulty, it can cause the machine to overheat and stop working.
5. Check the control board: The control board controls the various functions of the washer-dryer. If it is faulty, it can cause the machine to stop working.
6. If none of the above steps work, it is possible that the machine has a more serious problem that requires professional service.

It is important to refer to the user manual or contact Hotpoint technical support for further assistance and specific troubleshooting steps for your washer-dryer model. It is also important to make sure the machine is not plugged in before attempting any troubleshooting steps. It is also important to note that it is not safe to use a multimeter to test any of the heating element or thermostat

It is possible to replace just the bearing on your Hotpoint Aqualtis AQD970F 69 EU washing machine, however, it can be a difficult and time-consuming task. The best course of action would be to consult the manual for instructions on how to replace the bearing, or watch a YouTube video that specifically relates to your model. You may also be able to find the necessary parts on websites such as Amazon or eBay. However, it is advisable to get the help of a professional technician to do the job if you are not comfortable with performing the repair yourself.

How to remove the Key Symbol or Lock symbol off a Washing Machine.:watch video.!!!

If your Hotpoint washing machine is not starting after you replaced the electric door switch, there could be a few different issues causing the problem. Here are a few things you can try to troubleshoot the issue:

1. Check the power supply and make sure that the washing machine is properly plugged in and receiving power.
2. Check the fuse or circuit breaker to make sure that the washing machine is not tripping any electrical circuits.
3. Make sure that the door switch is properly installed and fully seated in the door latch assembly. If the door switch is not properly installed, the machine may not start.
4. Check the wiring and make sure that there are no loose or damaged connections.

That sounds like dry bearings somewhere or may be a slipping belt from a dry bearing. You need an engineer unless you can manage a full investigative strip down.

Here's info posted on Fixya before..hopr it helps. https://www.fixya.com/support/t14919952-hotpoint_hvl241_reached_spin_cycle

There are no internal fuses on washing machines. If the fuse is 'in the plug', it sounds like you are in the UK. In the US and Canada, our fuse is the contact breaker in the master switch board. Did you replace it with a 13 amp fuse? Did you check the fuse with a multimeter or in another device known to work? Help in the link https://www.google.com/search?q=hotpoint+futura+washing+machine+12kg+troubleshooting ..

Ideas here but you probably need service. Check the outlet with another item known to work. https://www.google.com/search?q=Hotpoint+WD640+model+will+not+turn+on ..

Could you be a bit more specific as to what this "Almighty noise" is? It will help to work out where the issue actually is. Is it a thumping noise? A rattling noise? a grinding noise? A humming noise? Can you post images of the sheared off piece of metal?

Hi, Please check the associated fuse in the fuse box of your home. We want to ensure that it's not been turned off or blown out (and needing replacement). Then, you can check the power source located at the washing machine itself to ensure that it still has juice by power items other than the washing machine. Thank you.

control board failed