20 Most Recent Hotpoint Aquarius WF000 Front Load Washer Questions & Answers


My washing machine wont start.

I have a hotpoint washing machine if I start the machine the water it's working after filling up the water the basket doesn't spin
12/29/2021 2:12:38 PM • Hotpoint... • Answered on Dec 29, 2021

Water still leaking

Look at and examine the door seal closely for any sign of a hole or tear in it.
If none is visible then it could be the clamp or spring that holds the seal to the drum front that is causing the prob..
Other than that , there could be a crack or hole in the container front.
9/19/2018 1:37:54 PM • Hotpoint... • Answered on Sep 19, 2018

I have a brand new

Clean the filter and pump
1/27/2018 6:12:13 AM • Hotpoint... • Answered on Jan 27, 2018

Hotpoint WF000P, On/Off light and

Your filter is partially blocked
10/11/2017 7:10:53 PM • Hotpoint... • Answered on Oct 11, 2017

Clothes still wet after fast spin cycle

Belt loose or motor / motor control board possibly defective
9/13/2017 3:51:08 PM • Hotpoint... • Answered on Sep 13, 2017

Please help

Be the first to answer 8/3/2017 9:15:03 AM • Hotpoint... • Posted on Aug 03, 2017Be the first to answer

Hotpoint wma11 where is the filter?

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Power off the mains. The filter is located behind the silver plate at the back of the machine at the bottom. Four screws hold it on. Drain out all the water. The filter is inside the big black rubber hose attached between the pump and the main drum. Remove the plastic clip holding it to the pump unit and then the metal cir clip holding it to the main drum. Inside is a white molded cone and a big white ball which floats. You will find a lot of junk here, clean out thoroughly. To refit put white cone back inside just as you found it, at the bottom, fit ball back into the cone. Attach to the bottom to the drum and re-fasten the cir clip. Finally reconnect the gator to the pump unit and tighten the plastic clip. Check out the pump too before reconnecting.

And rate me nice pl for the free help!

7/17/2016 9:49:07 AM • Hotpoint... • Answered on Jul 17, 2016

Wash machine stays on wash cycle and doesnt go to rinse or spin

If the water is not getting hot, this will probably stop the programme advancing .Check heater.
Plz rate solution to prob.
1/10/2016 10:13:53 AM • Hotpoint... • Answered on Jan 10, 2016

Aquarius wf440 is tripping rcd tried the element

remove plug from socket . and then remove motor plug if your able from motor .and test motor .
9/22/2015 12:43:56 PM • Hotpoint... • Answered on Sep 22, 2015

Motor removal for WF000

undo the bolts and pull it forwards....removing the plug of wires.... cheers
3/10/2015 7:50:42 PM • Hotpoint... • Answered on Mar 10, 2015

I have a Hotpoint Aquaris WF000, 1000 spin washing machine and when I put it on the lights flash and nothing else happens. What could be wrong with it please

Hi It seems to be a fault with this make of washing machine. I changed the door lock and that seemed to cure it for a while. However it now seems to be doing it again. What I have discovered is the following: Turn the washing machine off completely at the wall and pull the plug out - leave it out for about one minute and then plug it back in and switch on. This should cure the problem and it will work again. You may have to do this every now and again to clear some fault it has in the circuit board so leave some access to your plug socket. I hope this helps.
2/24/2015 3:03:00 PM • Hotpoint... • Answered on Feb 24, 2015

How do I remove the clips from the pump

I found it easier to hold one part with a Pointy nosed pliers and push the plastic grip out the side of the clip. As it is plastic it just ratchets back into place.
10/18/2014 11:05:50 PM • Hotpoint... • Answered on Oct 18, 2014

I need a switchboard for a hotpoint aquarius WF000

By switch board, I assume you mean the control module.
If you go to Hotpoint's web site, you should be able to locate the part you require.


Then click on-- SPARE PARTS AND ACCESSORIES in the menu on the left.
10/18/2014 11:01:35 PM • Hotpoint... • Answered on Oct 18, 2014

Hotpoint not drying clothes

Check the vent hose and the vent in the house for dryer lint. Excessive amounts will block airflow and the dryer senses that and shuts off the heat to prevent a fire.
10/15/2014 6:49:26 AM • Hotpoint... • Answered on Oct 15, 2014


A mouldy smell is often a sign of trapped residual water stagnating somewhere in the machine often just inside the door seal at the low point or in the filter.

Providing there is nothing like a old sock trapped in the pump or filter then there is not much you can do other than to dry the door seal and powder dispenser after use.

Please remember to rate this solution.
9/10/2014 8:37:34 PM • Hotpoint... • Answered on Sep 10, 2014
Not finding what you are looking for?
Hotpoint Aquarius WF000 Front Load Washer Logo

705 questions posted

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

Jesse Garza

Level 2 Expert

84 Answers

Lawrence Oravetz

Level 3 Expert

10558 Answers

Cindy Wells

Level 3 Expert

6528 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hotpoint Washing Machines

  • Hotpoint Washing Machines

Most Popular Question

hotpoint aquarius wf 250 off lights

  • Washing Machines