20 Most Recent Hotpoint Aquarius WD640 Front Load Washer/Dryer Questions & Answers


Plug off the wall. There is a thin rubber tube going from the switch area to the exit near the outlet tube. Probably this is blocked. This tube should be free from any blockage; take out the top clip from this tube and blow into it - it should be free, clear the blockage if any and refit. This is the water level tube which tells the machine when to switch off water, etc.....

Hotpoint... • Answered on Jun 02, 2019


An F-05 error message means that the pressure switch is jammed on empty or a problem with pump. The fault is associated with drain out (pump blocked or restricted in some way). Small panel at rear of machine reveals the pump, pull of the two pipes (Plastic clips hard to get off, slide them sideways), remove wire and unclip pump from base of machine by lifting locking tab and sliding to the left, pump can then easily be cleaned.

Hotpoint... • Answered on May 18, 2019


Hello,

F6 error is apparently a motor fault. The
motor could be jammed, open circuit ,
burnt out. It may just be a broken wire
or connection come off. Check the motor.

Hotpoint... • Answered on Apr 21, 2018


Check all thermostats , check to be sure you have 220 volts coming into the machine. Use ohm meter & check from heater element to the heater case or cabinet to see if the element is grounded. Positive to element & Negative to case should show no ohms if it does it is shorted. Also heater circuit runs through a centrifical switch on the motor so if the motor quits the heater shuts down so you don't have a fire. When the motor is not running the fan stops. You could check this switch but it don't happen very often. check this switch last. Hope this will help you

Hotpoint... • Answered on Feb 02, 2018


Hi from retired Englishman in SW France,

My list of Indesit (Hotpoint, Ariston) errors does not include an 'F06'!
If you have not done so already try checking that thre is no drainage blockage/stopage.

I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to rinse or spin or release the door lock if there is any water still left inside.
Following are my complete and hopefully 'coverall' pre-typed guidance notes for checking both the drain motor filter and the drain motor ;-0)
REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Hotpoint... • Answered on Dec 23, 2017


http://www.hotpointservice.co.uk/hs/pages/content.do?keys=FAQ:ERROR_CODES


F05 - Pressure switch jammed on full

All error codes at above link...

Hotpoint... • Answered on Dec 13, 2017


go to the parts website for Hotpoint for price or Google the part number and someone will post it for sale. Try going to You-Tube for instruction video on replacing. If it is still under warranty, call mfg or warranty company.

Hotpoint... • Answered on Nov 16, 2017


i can try to help you with this problem. if you pop the cap off the top of the agitator you will see a nut, once you take the nut off you should be able to jiggle the agitator in an upward motion to remove it then retrieve your wire and gently slide agitator back on so as not to ruin the splines if there are any. good luck

Hotpoint... • Answered on Sep 30, 2017


you could have a broken pipe on the filler or the seal has gone on the drum you would need to have a look, either way they are easy to fix or replace. drain pipe can leak if the pipe has come off the pump also check this but you will need to remove the case to get to look, always unplug the washer before touching any screws, remove case and look at the pipes and make sure they are seated in the right place.

Hotpoint... • Answered on Sep 09, 2017


You will need to replace the entire control panel assembly to cure this problem

Hotpoint... • Answered on Jun 29, 2017


Martha, Try running another cycle, for some reason I think machine is sensing it still has water in it. If after running another cycle dose'nt do it, check links below to see (2nd link) how to open door manually with out damaging machine. press the helpful button How to fix washing machine door lock in Hotpoint washing machine Opening locked washing machine door

Hotpoint... • Answered on Feb 10, 2016


This just happened to my hotpoint washing machine, I realise it has been a long time since this has been asked but since my answer is different from the others I thought I'd add it anyway in the hope it will be useful to someone one day. The fix was super easy, all that was wrong was the plastic knob itself, which had broken internally. I only found this out after taking the top and front covers off, which is an easy enough procedure, I did it this way: unplugged the washing machine, removed two screws from back of machine that hold top cover in place, then using a putty knife pushed between the top and front covers front to back right at the corners, thus releasing the top cover, once this was out I could unclip the front cover and get to the screws that hold the control board to the front cover. I unplugged the electrical connection to the board, removed all the screws and unclipped it from its plastic cover. At this point I could see the plastic knob had broken, I recovered the broken bit and glued it back on. After the glue dried, I just put everything back in place reverting the previous actions. Hope this helps. If you don't have glue or can't find the broken piece, you should be able to just buy another plastic knob off the internet.

Hotpoint... • Answered on Feb 06, 2016


bad earth or short on machine.............
needs checking out asap........
cheers

Hotpoint... • Answered on Dec 03, 2015


Hotpoint red led flashes Washing Machines Questions ...

www.fixya.com > Forum > Tags > red led flashes > Washing Machines
Hotpoint washing machines red led flashes related questions and answers. ... then off When i turn on the washing machine - Hotpoint wf640p - the LED display flashes all the 8s (so ... Question about Aquarius WD640 Front Load Washer/Dryer.

Hotpoint... • Answered on Oct 27, 2015


You can't "Reset it" as such, you need to fix the fault. Is this the F11 issue you reported before, or another problem?

Hotpoint... • Answered on Oct 14, 2015

Not finding what you are looking for?
Hotpoint Aquarius WD640 Front Load Washer/Dryer Logo

906 questions posted

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

gbob59

Level 3 Expert

3063 Answers

Cindy Wells

Level 3 Expert

6259 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hotpoint Washing Machines

  • Hotpoint Washing Machines

Most Popular Question

machine fault code f13

  • Washing Machines
Loading...