20 Most Recent
Hotpoint WMA58 Front Load Washer - Page 3 Questions & Answers
A BLANKET THAT SHOULD HAVE BEEN DRY CLEANED, PUT
Remove the lower rear cover then disconnect the large black hose from the bottom of the outer tub. Remove the filter from the hose and clean it. Put and secure the hose back into the bottom of the outer tub.
Only takes on cold water will not take on hot when
If it is a hot and cold fill washer with 2 seperate inlet hoses, and no hot is entering, then either the hot inlet valve is faulty, or the valve is not getting an electric feed to it.
Make sure that the programme you select is ahot prog, as many of the programmes are3 cold fill only.
When on final spin, water leaks from detergent
You probably need to clean the filter.
Remove lower rear cover of washer.
Remove large black hose fastened to bottom of drum.
Remove and clean filter inside hose.
Remove hose onto pump, and check for blockage or obstruction here as well.
Please rate my solution.
Thankyou.
Cant remove top of front loading washer
Remove the four screws at the top rear of the top panel that go through the hinge brackets(bare metal in color), then lift up the top panel and push toward the front of the washer while lifting, it may take a firm lift and push, work with it and observe how the top and sides are connected once you have lifted the rear of the top panel. Good luck !
Hi. My wma58 is leaking from the detergent
I removed top panel of machine took out drawer and removed screws allowing me to pull drawer compartment back slightly from front panel. Here i found more detergent residue which i couldn't see before.after cleaning this and refitting everything problem was solved.
How to remove back from machine
There is a small cover at bottom rear of washer, this is the only access into the washer from the rear.
Simply undo the pozidrive screws, and remove cover.
Any other access is from the top, or by removing the front panel assy.
Hope this helps.
It seems that the drum is spinning off its axis
When a front load washer does not spin properly, the problem can be caused by failed axle that connects the pulley to the wash drum, or failed shock or (possibly) broken suspension springs.
Remove washer top, inspect the two or four springs holding the washer drum up. The whole drum should be able to "bounce" a little, when you press down on it.
Remove the lower front panel and with a flashlight, inspect the two shock absorbers. Both should attach up to the wash drum, but it is common for them to break, especially if the front load washer has been moved from one house to another without re-installing the lower brackets and the long bolts that secure the drum during the move.
If the springs and shocks are not damaged, with the top removed look down into the rear area. You will see a large pulley with a belt on it. If you see brown/black grease marks all over or obvious problem when you try to turn the pulley, you have found the major problem.
Please get back to me with what you find. OK?
Where is the filter
The filter is to be found at the rear of the washer.
Remove lower rear cover.
Remove large black hose fastened to bottom of drum.
Remove and clean filter located inside the hose.
Remove hose onto pump, and check for blockage or obstruction here and in the pump as well.
Hope this helps.
My 13 year old wma58 makes a lot of noise on spin rinse
To be certain if it is the main bearings, remove the lower rear panel of washer, remove belt, and spin drum from the front.
If it feels rough or is rumbling, then the bearings have failed..
If no noise from drum then it could be noisy motor bearings.
At that age, it certainly would not be cost effective either way.
Hope this helps.
Hi i am having trouble with our wma58, the last 2
Try the following.
Remove lower rear panel of washer.
Locate and remove the large black hose fastened to the bottom of the drum.
Remove and clean the filter inside the hose.
Remove the black hose onto the pump, and check for blockage or obstruction here and in the pump.
Hopefully, this will solve your problem.
Good luck.
Why does my washing machine trip the electric
run the machine, after it trips, unplug and carefully touch the motor,it may have a bad capacitor, or dry bearings causing it to draw excessive current,if these 2 things are not it, then look for a bare wire that may be touching case during this part of the cycle,and if you can get an "Amprobe" it reads current and check machines current draw during the start to trip current
Is it possible to change bearing on a Hotpoint
You can do it your self, but it is a very involved repair, and I would not recommend that you attemt it, unless you are conversent with washing machines, it involves a complete strip down.
Please rate my solution.
Thanks.
Not finding what you are looking for?