Hotpoint Aquarius WMA42 Front Load Washer - Page 2 - Answered Questions & Fixed issues
How to I remove the drum from a Hotpoint WM64
Remove top cover and rear panel.
Remove belt and drum drive pulley.Remove clamp that secures door seal
Remove top control console panel.
Remove door lock.
Remove screws top and bottom holding front panel, remove front panel.
Remove spring clips holding plastic drum front, lift to one side plastic drum front cover.
Tap drum shaft to remove drum from container, remove bearings.
Please rate my solution.
Thanks.
4/21/2014 1:42:29 PM •
Hotpoint...
•
Answered
on Apr 21, 2014
•
1,715 views
Water wont pump out code f-05
I am not sure what that fault code means but you should be able to find the codes on the Internet.
I would suspect that the problem is a jammed or blocked or faulty drain pump. As has been sugested drain by gravity by lowering the hose into a bowl to the floor, -----REMOVE THE PLUG FROM THE SOCKET. ---- Inspect the pump, see if it is blocked or jammed, the hoses come off quite easily. Clear any rubbish out and see if the pump will then run by selecting pump and spin cycle when plugged in.
It is a good idea to take the thin pressure switch hose off at the switch end and make sure that it is clear through to the bottom by blowing down it. Make sure the machine is unplugged first.
Gently blow the switch too, you must get 2 clicks , first one with a gentle blow, and another with a slight increace in pressure.. Refit all hoses securely.
Hope that will solve your problem.. Sam.
4/14/2014 3:58:40 PM •
Hotpoint...
•
Answered
on Apr 14, 2014
•
70 views
How to change the brushes
The motor is situated rear centre of the machine. It's best to remove it, either tip it back, ensuring it's stable and supported or remove back panel for access. Brushes are located on either side of the motor.
3/24/2014 11:58:40 PM •
Hotpoint...
•
Answered
on Mar 24, 2014
•
50 views
Drum doesnt turn
hi is the belt on if so 1st thing to check are the motor brushes good chance thats the proplem
2/17/2014 12:58:46 AM •
Hotpoint...
•
Answered
on Feb 17, 2014
•
86 views
No water supply error
is it dirty water
possible it is from the sink when you do your cleaning
the pipe needs to be lifted higher
2/12/2014 9:06:42 PM •
Hotpoint...
•
Answered
on Feb 12, 2014
•
27 views
H20 ERROR SPIN DRYING
The error indicates a problem with the incoming water supply.
Check for restricted or kinked inlet hose/s, check that tap/s are fully turned on and that you have adequate water pressure.
1/24/2014 12:31:51 PM •
Hotpoint...
•
Answered
on Jan 24, 2014
•
610 views
Replace door seal
its quite easy on this machine,you can view a video on Espares.co.uk or remove front panel ,seven screws 4 top 3 bottom unclip wire on seal at front seal has two large clips to secure one outer and one inner, I find it best once the front panel is loose to unscrew the door interlock to fully remove cover once this is done you can see the workings and the exposed seal good luck.
11/3/2013 9:36:24 AM •
Hotpoint...
•
Answered
on Nov 03, 2013
•
96 views
Water does not drain away.
You may have a clock in the hose. If the rinse cycle doesn't work it could be a board problem. Try unplugging the machine first to reset the board. Also try to see if the end of the drain hose has anything in it that is blocking the water.
10/15/2013 8:28:57 PM •
Hotpoint...
•
Answered
on Oct 15, 2013
•
100 views
Aquarius filter
its located within the sump hose ,located bottom of drum and connected to pump, its a black hose with white clips.Plastic filter is in here..
10/2/2013 9:27:31 PM •
Hotpoint...
•
Answered
on Oct 02, 2013
•
44 views
Hotpoint wmf 720 H20 fault
If it tries occasionally to fill on rinse for a short time and pumps out/drains if the hose is flat on the floor but the programming seems off, its the motor carbon brushes worn down.To prove it if you have no spares, remove the brush holders and gently stretch the carbons out of the holders a little bit so that they touch the commutator in the motor when refitted. The copper pigtail will usualy give about 2mm stretch if you are careful.It will maybe work for a few days whilst you get new brushes.
9/19/2013 1:42:58 PM •
Hotpoint...
•
Answered
on Sep 19, 2013
•
1,942 views
There is something stuck in between the drum and
Disconnect the machine. If you can get hold of a wire and put it in between the drum and the cover. If that does not work get out the manual, and look for how to open the drum.
If the manual does not help you, try screwing the back off and lift the drum and put a wire in between the drum and the cove. I hope you can loosen what seems to be stuck.
Kolbrun
8/30/2013 6:18:11 PM •
Hotpoint...
•
Answered
on Aug 30, 2013
•
130 views
Not finding what you are looking for?