20 Most Recent Hotpoint RGB745 Gas Kitchen Range Questions & Answers


it very well is the door switch might be stuck. The way to unstick it is to slam the door. Very often it'll jar the switch loose if that doesn't work you'll need to order one. Easy to install there are youtube videos on it. If you need the part...try here...repairclinic.com or appliancepartspro.com. Hope this info helps a little.

Hotpoint RGB745... • Answered on Jan 04, 2018


If you are sure you have the correct clock for your model have followed instructions completely, tape up loose wire ends individually and give it a try.

Hotpoint RGB745... • Answered on Sep 07, 2017


Hello Michael Smith, You MODEL number only came through as a PARTIAL ... (so I filled in the rest (assuming USA)): RGB745 ... wea2ww Please note: Accordingly... you will have to VERIFY the part. Part and video guidance are available here: Third item on the page "heat sensor" http://www.appliancepartspros.com/parts-for-ge-rgb745wea2ww.html Hope this helps... Carnac the Magnificent

Hotpoint RGB745... • Answered on Aug 13, 2017


They will require a cleaning of the tubes and orafices. Blow out with compressed air.

Hotpoint RGB745... • Answered on Nov 11, 2016


Hello. The range you have has a spark ignitor module inside the top, beneath the cooktop. Also, there is a spark ignition harness that has the four switches(snapped onto each of the burner valves at the control panel) connected together(daisy chained) that goes to the module and the incoming 120v supply. HOWEVER, the bigger issue here is getting to the module, harness, and other parts beneath the cooktop. Gas ranges are notorious for having the mount screws seize in the burners. When removing them is attempted, the heads usually snap off causing burner replacement to be necessary(which is why I listed the part numbers for the burners and screws). The cost of this can be high. I suggest calling for service if you are at all hesitant about working on the range. BURNER SCREWS(8) WB1K84 BURNER HEAD RR WB16K12 BURNER HEAD LF WB16K11 BURNER HEAD RF WB16K10012 SPARK MODULE WB13K25 HIGH VOLTAGE HARNESS WB18K06

Hotpoint RGB745... • Answered on Oct 10, 2015


Make sure igniter is getting power before you replace it. Also check the switch that feeds the igniter. For parts go to attached. Search Over 2 1 Million Appliance Parts

Hotpoint RGB745... • Answered on Oct 07, 2015


You may find that your new oven cooks differently than the one it replaced. Use your new oven for a few weeks to become more familiar with it. If you still think your new oven is too hot or too cold, you can adjust the thermostat yourself. Do not use thermometers, such as those found in grocery stores, to check the temperature setting of your oven. These thermometers may vary 20-40 degrees. NOTE: This adjustment will not affect the broiling or the self-cleaning temperatures. The adjustment will be retained in memory after a power failure. Adjust the oven thermostat-Do it yourself! To Adjust the Thermostat Touch the BAKEand BROIL HI/LOpads at the same time for 2 seconds until the display shows SF. Touch the BAKEpad. A two digit number shows in the display. The oven temperature can be adjusted up to (+) 35°F hotter or (-) 35°F cooler. Touch the + pad to increase the temperature in 1 degree increments. Touch the - pad to decrease the temperature in 1 degree increments. When you have made the adjustment, touch the START/ON pad to go back to the time of day display. Use your oven as you would normally. NOTE: This adjustment will not affect the broiling or self-cleaning temperatures. It will be retained in memory after a power failure

Hotpoint RGB745... • Answered on Mar 24, 2015


"bad line" error means the control panel is not seeing a proper voltage to the oven. Have the power connections checked with a voltmeter all the way to the control panel. If voltage is present, you may need a new control. 25316221-dz1fkxf1fwolart5ai0divhk-4-0.jpg

Hotpoint RGB745... • Answered on Dec 10, 2014


Your range uses electronic ignition, not pilot lights. For surface burners the igniter sparks when the gas valve is turned to the "light" position. All burners should spark when any gas valve is in the light position. For the oven the ignitor is also electric but does not spark but rather heats up or glows. What is the problem with your range?

Hotpoint RGB745... • Answered on Dec 05, 2014


Hot point has 2 pilot lights on top... light them... then go to oven and light that one... it is a safety feature... no pilot on top kills the pilot in the stove.
.. since gas is heavier then air the company made sure if there was a gas leak on top that it would not be caught by oven and blow up.

Hotpoint RGB745... • Answered on Dec 02, 2014


Go to the manufacture site search for manuals on their site for the oven you have... usually PDF format

Hotpoint RGB745... • Answered on Dec 02, 2014


For the last 10 years or more there are no pilot lights on gas ranges. Modern ranges have an electronic igniter on the burners and a different type on the oven.

Hotpoint RGB745... • Answered on Nov 30, 2014

Not finding what you are looking for?
Hotpoint RGB745 Gas Kitchen Range Logo

451 questions posted

Ask a Question

Usually answered in minutes!

Top Hotpoint Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Cindy Wells

Level 3 Expert

6259 Answers

jdthefixer

Level 3 Expert

747 Answers

Are you a Hotpoint Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hotpoint Kitchen Ranges

  • Hotpoint Kitchen Ranges

Most Popular Question

hotpoint gas range rgb745 electric

  • Kitchen Ranges
Loading...