Questions & Answers
Need cord for LT765
The power adapters are available here:http://www.ccl-la.com/catalog/product_info.php?products_id=48
My monitor MAG lcd 16inch
In case you haven't done it already, please connect the monitor to the computer and turn everything on and let it boot up. While the screen is black, take a flashlight and carefully hold it against the screen. If you can see that the LCD portion of the screen is working, then continue reading. This model seems to have a number of complaints against it. That being said, many people seem to believe that caps become swollen just because that's what they do. In my experience, for multiple caps to swell or need replacing, it takes a long duration over-current event or a short duration death event. The most common long duration over-current event in a monitor is burned bulbs and/or burned transformer. The most common short duration death event being a power surge (blackouts, lightning, or connected to the same breaker as an air conditioner or microwave) If you have successfully replaced the caps, then you already show some technical prowess. Search your main board model number for some more info. If you can read the tiny part numbers on the transformer, search for a datasheet to find a way to test it with a meter. Bulbs are a bit harder to do. I've done it, but it is almost impossible to keep even a single speck of dust from entering the insides. If you get to the bulbs, and they are blackened on the ends, you can be fairly certain that they are burned and creating an over-amp condition in the driver circuits. Best of luck to you.
I just installed a MAG 17 incuh flatscreen monitor
I think that you have chosen some settings that are not compatible on it ..resolution too big and probably the refresh rate high ..
first from the monitor settings ..press the auto-settings button ..and let it make the proper choice ..after that ..to eliminate any settings in the video card that might affect it ..boot your computer in safe mode..and remove the video card driver from control panel ...add /remove programs ...and after that run it again from the disk or ..from teh support site if you do not have the disk ..
If you only have the on board driver..and you do not have a disk ..run it from the drivers of the motherboard disk ..This will reset the odd choices on the video card ..and make it work ..to open in safe mode..press F12 on start ..and choose safe mode..(for some computers the button is F9 or F8 )Usually the button is specified when it boots up ..
But ..for to be sure that this is the cause...you have to hear to computer running ..and only the display to be black ...otherwise can be a physical fault..
Hooking up to mu computer the monitor states no
Is the monitor set to the correct input source? Is the cable fully seated on both the computer and the monitor? Try a new cable. Is the computer sending the video signal to that port that has the cable? Laptops sometimes need the external video port enabled in the BIOS, for example. Check your manual to access the BIOS; frequently it is F1, F2 or ESC pressed before the OS starts to load. Some newer desktop computers do not have the VGA port enabled initially as well.
I hope this helps.
(on my Win7 desktop and laptop, to turn on a second monitor it is under Screen Resolution (shortcut from the desktop by right-clicking anywhere there isn't an icon or running program).)
I bought a mag innovision model 780 monitor at a
With Most Mag monitors, the plug is a simple 3 prong on the bottom side of the monitor. Though it isn't proprietary, it isn't a common power plug either. Radio Shack does carry this type of cord. Just look on the bottom side of the monitor itself. the three round plug "thingy" is where the 110v plugs in straight from the wall. Best of Luck!
Speakers not working
I haven't seen a monitor that needs drivers for the speakers.
Assuming it has a standard 3.5mm plug for sound input from the PC, have you plugged this in between monitor and PC?
The monitor will have a volume control, make sure it's not muted or turned down too far.
Also check the volume control panel on the PC to make sure it's not muted or turned down.
Message states mode not supported
If you are talking about dual screen mode, some monitors do not support this. And some do not support dual screen at the current resolution setting. Play with the resolution by right clicking an open area of your desktop, then click properties, and then advanced. There should be a slider indicating resolution (in xp at least) After that, then the monitor itself does not support dual screen. Best of Luck to you!
Power supply to Mag 780 Model
No, it has a normal, seperate power cord. But the socket in the monitor is very small, it's a small round one. When facing the monitor from the back, it's located directly to the right of the monitor-stand, at the bottom-side of the screen. Just put the monitor on it's side to see it clearly.
It's all explained with pictures in your monitor's manual which you can download from the official website here: http://www.maginnovision.com/Support/Downloads.aspx?sn=464
Not finding what you are looking for?