20 Most Recent Proview PL713S 17" Flat Panel LCD Monitor Questions & Answers

0helpful
1answer

I recently hooked my Proview monitor 700P PL713S

may be your monitor is not having audio facility so u may try with small woofer which available in the market @400 or 500
12/13/2017 4:09:28 AM • Proview PL713S... • Answered on Dec 13, 2017
0helpful
2answers

How to use this Proview LCD Monitor 17" 700P AS A TV Screen

No. The newer LCDs can do both. But they are a TV to start with the option to hook up a Desktop.
1/12/2015 4:53:58 AM • Proview PL713S... • Answered on Jan 12, 2015
0helpful
1answer

Proview Monitor model 2200W. The brightness and

i have a proview 2200w it comes on for about 3 seconds and goes off with the blue light still on
12/21/2014 10:00:18 AM • Proview PL713S... • Answered on Dec 21, 2014
0helpful
5answers

Power Surge damage. Suggestions on which part to replace.

I would start looking at the power supply, it's usually a separate board where the a/c line plugs into. In many cases i have seen that the problem you described is from a damaged power supply, sounds like something is shorting causing the power supply to continuously come on and off. I would first check the capictors to see if any of them have blown, usually cylinder looking and sometimes you'll see an X or a K at the top of the cylinder, if it's blown then the top will be bulging out instead of being flat. If all those look good then there is probably a short somewhere else like in one of the transistors, if so you'd be best to just find another power supply board to replace.
12/1/2014 4:38:18 AM • Proview PL713S... • Answered on Dec 01, 2014
0helpful
1answer

Can't set resolution on 700p

Refer to its user manual.
8/12/2012 2:00:27 AM • Proview PL713S... • Answered on Aug 12, 2012
0helpful
1answer

Insignia 22" flat screen tv.

I'd guess that the surge damaged some resistors on the internal circuit board, possibly a capacitor. You may be lucky if this has an internal fuse, in which case the fuse may have blown, saving the main components. Best course of action is to take it to a TV repair shop or similar to have it checked out
7/20/2011 11:21:24 PM • Proview PL713S... • Answered on Jul 20, 2011
0helpful
1answer

My screen keeps going black

Does it do the same when used with another PC, all cables are good?
If it is the monitor, then please read below.

If you are going to DIY and already try the monitor with another PC, and have proper tools and know safety precaution then please read on: Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply (they should be replaced in a set), blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/albums/yy352/budm/ Post back what you see inside so we can guide you further and it will help out other people in the future also.

Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors pictures: http://s807.photobucket.com/albums/yy352/budm/

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC series.

4/20/2011 6:05:14 AM • Proview PL713S... • Answered on Apr 20, 2011
0helpful
2answers

Can you make the monitor

Not without some serious modification. I wouldn't recommend undertaking that project unless you either have some previous experience modifying electronics, or you want to risk breaking the device.

Here's a touchscreen monitor that you can purchase: http://www.newegg.com/Product/Product.aspx?Item=N82E16824176142

Here's some information about modding a touchscreen overlay onto an LCD. http://beta.ivc.no/wiki/index.php/Eee_PC_Internal_Upgrades#Touch_screen This is specifically for an Eee PC, but the method would apply to a regular LCD. As you can see, it is quite a lot of work.

I hope this has been helpful.
3/4/2011 7:16:10 PM • Proview PL713S... • Answered on Mar 04, 2011
0helpful
1answer

My monitor shuts off after 1 second run time, what

It can be the power supply, backlights inverter, lamp assemblies.
If you are going to DIY and already try the monitor with another PC, and have proper tools and know safety precaution then please read on: Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply (they should be replaced in a set), blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/albums/yy352/budm/ Post back what you see inside so we can guide you further and it will help out other people in the future also.

Basic LCD monitor and TV troubleshooting guide: http://www.fixya.com/support/r6150077-basic_lcd_monitors_troubleshooting http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide http://www.fixya.com/support/r7406380-tv_training_manuals Failed TV and Monitors: http://s807.photobucket.com/albums/yy352/budm/

Learn about bad caps: http://en.wikipedia.org/wiki/Capacitor_plague

Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you. Or www.digikey.com just make sure to use caps with low ESR, 105c, high ripple current, long life rating such as PANASONIC FM or FC

2/22/2011 3:20:39 AM • Proview PL713S... • Answered on Feb 22, 2011
0helpful
1answer

W Thought it was the

A good rule of thumb to follow is: if the power button turns orange/red when it goes out, it's usually a problem with the monitor. If it stays blue or goes off, it's a problem with a driver or cable connection. Good luck!
11/24/2010 3:22:33 PM • Proview PL713S... • Answered on Nov 24, 2010
0helpful
2answers

I cannot find the power cord to my monitor. Where

The power cord can be purchased at a computer shop of your choice, standard 3 pin power cable. Same as that used for the power to your computer.

damnor01
11/22/2010 1:51:51 PM • Proview PL713S... • Answered on Nov 22, 2010
0helpful
1answer

Blurry screen on proview tft monitor

Try to adjust the picture adjustment.Like the contrast and brightness
10/6/2010 3:14:08 AM • Proview PL713S... • Answered on Oct 06, 2010
0helpful
1answer

I have a proview 22 inch monitor model 2200w it

Check power supply DC filter caps first.
If you are going to DIY and have proper tools and know safety precaution then please read on:
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply (they should be replaced in a set), blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague
http://www.badcaps.net
Capacitors kit: http://lcdalternatives.auctivacommerce.com/ he can make you a set of caps for you.
8/22/2010 10:48:38 PM • Proview PL713S... • Answered on Aug 22, 2010
0helpful
1answer

Screen is blank

Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, blown fuses; poor solder joints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague
http://www.badcaps.net
7/5/2010 1:26:42 AM • Proview PL713S... • Answered on Jul 05, 2010
0helpful
2answers

My proview PL713s will not display an image!

I'm having the same problem. Did you ever figure what went wrong?
4/23/2010 2:10:33 AM • Proview PL713S... • Answered on Apr 23, 2010
Not finding what you are looking for?
Proview PL713S 17" Flat Panel LCD Monitor Logo

65 questions posted

Ask a Question

Usually answered in minutes!

Top Proview Computers & Internet Experts

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2028 Answers

Brad Brown

Level 3 Expert

18851 Answers

Tom Chichester

Level 3 Expert

62196 Answers

Are you a Proview Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Proview Computers & Internet

  • Proview Computers & Internet

Most Popular Question

make monitor

  • Computers & Internet
Loading...