20 Most Recent Miele 23 in. Novotronic G841 Built-In Dishwasher - Page 3 Questions & Answers

Hello, Welcome to Fixya. The issue is likely just the blower and housing drain hose blocked with "dirt" from time & use. First things first...**turn off the power via the breaker at your home service panel...safety first** Now you will need to take the door panel off ( watch those edges they are VERY sharp ) and unfasten the control panel as well, the screw`s are around the perimeter of the door facing the dishwasher tub opening. Once you have the panel off, you will then unscrew the round part surrounding the vent fan inside the door ( it turns about 1/4 turn counter-clockwise ) the fan motor assembly can be pulled off the door and cleaned out. You should now remove the small rubber drain line from the fan to the tub which is routed inside the door panel & clean it out as it too gets plugged hence, not allowing the condensation to run back into the tub to be pumped out so when you open the door it pours onto your floor. Hope you find that helpful. Let me know how you make out or if you require further assistance. Thanks for visiting "FixYa" for your repair questions. Please take a moment and rate the solution provided here for you. Sorry this solution is so condensed, it just appears this way when using my iphone no matter how I space it when writing. Good luck. Regards, Macmarkus :)

The fault is possibly linked to the water intake circuit.

Either the inlet tap is closed or the water inlet filter is blocked or the intake valve is simply faulty.

See pages 33 and 46 in the user manual.

Hope this helps fix the problem. Please rate the solution if suitable or post a comment.

Get all of the water out and make sure that the drain in the bottom is not clogged

sounds like the flood switch has activated.

You will have to drag the dishwasher out from under the counter after turning off the power to it. Tilt to one side so that any water collected under it is expelled. This will free up the flood switch. Wait about 30 minutes and turn the power back on.

There could be a leak of some sorts from the door seal or hoses which is causing the water to collect.

Hope this solves the problem. It is unclear why none of the lights are lighting up to show a fault condition.

Hi


Thanks for using FixYa. The first thing that should be checked is if its draining properly as it could be that the drain hose is clogged and needs to be cleaned. The drain pump also should not be clogged. Also the stopcock should be opened fully and the water inlet valve should be checked for any clogs. Also the metal filter, impeller cover and the air gap unit should be checked. After checking this you can reset the error as follows: turn the rotary selector switch to "Stop/End" or press the "Start/Stop" switch for approx. 5 secs. Then switch the appliance off and then back on again. Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

hi,

most common faults with dishwashers is a drain fault. Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drilled out large enough. This then causes a blockage. Also check the non return valve under the filter and make sure the drain pump can turn freely.
Hope this helps.

most common faults with dishwashers is a drain fault. Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drilled out large enough. This then causes a blockage. Also check the non return valve under the filter and make sure the drain pump can turn freely.
Hope this helps.

hi,

you need to adjust the door tension springs which is by a screw each side of the hinges on the plinth of the unit at the front. There is a symbol of a spring to show you which screws to release. do them evenly and the door will not spring up,

hi,

what you need to do is slack off the spring tension on the door hinges. each side of the unit at the base on the plinth there is a screw with a spring symbol next to it. turn this anti clockwise to reduce the spring tension.

Hope this helps

With the reformulation of detergents, it's becoming a common problem. You can try a liquid with water softener in it, and slightly hotter water. It might help. The environmentalists have made the manufacturers reformulate a lot of cleaning products to the point that, vinegar and water is almost as good as the newer detergents.

hi,

this is a general fault light which could mean anything without a Miele Technician coming out and connecting a laptop to the unit. However most common faults with dishwashers is a drain fault. Check for any kinked hoses and check the drain spigot under the sink where the drain hose connects into the u bend. Usually this is where food gets trapped due to the spigot not being drilled out large enough. This then causes a blockage.
Hope this helps.

complain to miele be a pain they have given discounts on a new one before. try running apple cyder vinager through it pore some in let it run a little then open the door and let it soak for a day or so and then try it again it may just be dirty good luck

rarely. next time this happens. immediatly go to the breaker box, and feel for heat on the breaker that is blown. if it is warm, your miele is okay, call an electrician.

Hello Stonegroup,
The impeller is located below the bottom filter trap. Remove the tray and at the twelve 'O' Clock position you will see a small opening. Inside there are the pump impellers. take the Hackenschlussel (Hook spanner/Miele tool) and insert it in the opening and turn. You should turn it a few times and be able to feel the impellers free up. Also, Make sure you run the dishwasher atleast once a monch to avoid the circulation pump getting stuck like this

hello i'd check to see if theres a glass fuse in side the dishwasher it will be on the power board good luck

shaun

Add the requested rinse aid.. The light is on telling you it's low/empty.

I had a similar problem with a different Miele. I found that under the door, there is a removable trim panel (may not be one on yours). Under the trim panel was an acoustically sealed metal plate held by a couple of screws. i switched off and disconnected the electrity, then removed the plate. The bottom tray was filled with a big puddle. I cleaned that up and put the machine back together and it ran fine. Accordingly, I'm getting some replacement shaft seals for the thing as it looks like its worth fixing. Good luck with yours. rupertvdP