Top 20 Homelite Ignition Chip Replaces Points Condenser Xl12 - Page 3 Questions & Answers

The filter is always attached to carb, otherwise it would not an air filter https://www.gardnerinc.com/manuals/pdf/ipl/TTI/Homelite/blowers/UT09526_598/UT09526_598_r_01.pdf

A google search produced the link below. https://www.docssuite.org/manuals/?brand=Homelite&utm_source=google&utm_medium=cpc&utm_term=homelite%20owners%20manual&utm_network=g&utm_pos=1o1&utm_campaign=FindProductManuals_v2MB+11-26&gclid=Cj0KCQjwnpXmBRDUARIsAEo71tQO_TphRpB3usT1MftRxxUenUiew3THlj4V5cgjUX7NILyu2WfOOz0aAtxwEALw_wcB You would be fairly safe using a 2-stroke mix similar to machines of a similar age, design and purpose if you don't find what you are looking for.

Check with Parts Tree Repair Clinic they will help.

yes it can be replaced. any lawn mower parts store will have this bulb. there are two screws that hold it on. take it with you to get a new one

Take it to Ace Hardware and they will get you the correct chain.

Turn H and L jet screws all way to right back each one out 1 1/2 turns. Start and hold full throttle, adj. H for maximum speed then adjust L so it will idle and have very little hesitation when sudden increase of throttle. Once this is done you may have to adj. H a bit more for maximum speed.

The short line in the tank (about 1/2 inch in tank) goes to fitting just below primer bulb. The other line that goes to bottom of tank with filter attached goes to other fitting.

31.1
http://www.acresinternet.com/cscc.nsf/ed1d619968136da688256af40002b8f7/599a10777002057f88256c260047d374?OpenDocument

Normally remove the two screws holding the cylinder. Pull cylinder from piston. Then remove the snap rings or springs on one side of piston pin and gently drive out pin with brass rod or hard wood pin.

Standard plug gap for a chainsaw 0.5mm

I do not have a Homelite blower, however Your symptoms seem to be pertinent to all small engines of that ilk. I have had several Weedeaters that did the same thing and I found that the cause was leaving fuel in the tank over the winter and the gas part of the fuel evaporates leaving the oil part as a residue that gunks up the carburetor and the jets do not feed fuel properly. If you use alcohol gas along with the oil at a proper ratio, the gas left in the machine leaves the water that the alcohol contains adding to starting woe.The simplest thing to do is to get some starting fluid and exposed the air filter so you can spray a generous amount into the filter. (Be careful, the starting fluid is very volatile and may cause a fire) When the blower starts, keep spraying a shot into the air filter until the machine seems to run. by jiggling the choke you should be able to smooth out the running. Eventually after several tanks of fuel should clean out the solidified gunk.

Would need model number

How to Remove the Cap to Replace the Line of Homelite Trimmer Homelite UT33600 Operator Manual General Maintenance Advancing Line...

try service manual via http://www.manualsonline.com For your machine. Depending on age the "clutch" is not engaging on the shaft for some reason. It may be that some screws have come loose or missing. You may need to buy a new recoil mechanism.

50 :1 using stihl special 50:1 oil it covers all ratios regardless

refer to owners manual, look at existing spark plug, or type in search engine Homelite 26 B leaf blower spark plug

Fully close the choke, shut off switch is toggled to "run". Pull start without using the throttle until the engine fires. Set the choke to the second position, pull start again until the engine fires and idles. Allow some time for the engine to warm up while giving light throttle and when the engine responds smoothly, set choke to fully open.

Remove fuel lines at Carb. Blow carburetor cleaner through lines into tank. Spray carb. 1/4 cup carb cleaner into tank shake thoroughly pour out and repeat until clean. Blow out fuel lines into tank with compressed air and blow out tank with compressed air.