20 Most Recent
Homelite Ignition Chip Replaces Points Condenser Xl12 - Page 10 Questions & Answers
Tune up st145 homelite weed trimmer
Hopefully this diagram will transfer.
1. Remove fuel clean fuel tank and check fuel lines for breaks or holes.
2. Clean or replace sparkplug.
3. Clean screen item no. 4 in muffler
4. Clean or replace air filter item no. 31
Chain oiler not working
Hopefully this diagram will come through if not go to homelite.com, service and support, find parts, parts locator, model xl then to engine internals. You probably have a bad oil pump and these are parts and numbers you might need.
4. Spring..69447
5. Gasket 2 each 69244
6. Plunger A12356B (most common problem)
7. Oil pump body 693431
8. Ball 60051
9. Spring 68570
Ive got a homelite 720
Please list your model number when posting and I might have found part number for you.
Go to homelite.com service and support, find parts, parts locator, model # if you cannot find model number go to product line, homelite, then select generator, without model number you will have dozens of generators to look at.
I need any info on a 20 in homelite super xl automatic ut#10045c.such as year made, fuel mixture, how many cc'so it is. All information that I can get will be great
I bought up a lot of Homelite parts when dealer went out of business about 20 years ago and have had interest in them since. I have worked on a few super xl's but cannot tell you for sure the fuel mixture but believe it probably changes over the years from 16-1 to 20-1 saw on internet one person claimed that that ut number used 32-1. Don't believe it would make any difference as long as you used good grade 2 cycle oil and it would not smoke near as bad as 16-1. One person on internet claimed that he still had the saw his Dad bought new in 1967 or 68 so they have been around that long but at that time I do not believe they had a UT number on them.
The cc is 57.4 and weighs 13.14 lbs. With 24" bar.
What is gas oil mixture for a Homelite 33 cc Ranger?
50:1--( 50 parts fuel to 1 part oil)
Now you can buy a special oil from Stihl service agents that has a 50:1 formulation that will cover all mix ratios regardless of the engine make or ratio requirement
saves having different tins for different ratios for different engines
Carb settings for Homelite weedeater ST-275
Set both the H and L for 1 1/2 turn out from bottom, start and adj. The H for max rpm for full throttle, now set the low for good idle and very little or no hesitation when opening throttle. Now set H for max rpm again and then back off until you get more of rumble at full throttle.
Hello. I Need to Fit a New Starter Cord to a Homelite Strimmer, Can You Give Start to Finish Instruction's. UT No is 20586, Ser No is HM2130442.
Thank's,
Mike.
Hopefully the website will translate. Remove throttle handle from shaft trying to keep all parts in one side and once removed place together and install a couple of screws, remove shaft from part no 42 by loosening screw no. 43, item 45 has either a allen head or star head screw in it will probably loosen ccw. Remove item 45, remove item 46 should be arrow to show which way to turn you will need to use copper or brass pin to hit with hammer to remove to prevent damage. Now remove item no. 41 and you are at the starter cord. You will now have to remove spool no 51 and notice how rope is wound if possible, remove old rope install new rope place spool back in place to where it catches spring as it should now wind in same direction as rope wound about 5 turns hold and run rope through eyelet of starter housing. Now install keeper 52 with screw 53.Sorry link did not work just go to link below and type in your ut no. then select homelite.
https://www.ereplacementparts.com/homelite-hlt17c-ut205
Not finding what you are looking for?