20 Most Recent Miele Novotronic T230C Electric Dryer - Page 3 Questions & Answers

Most likely fault is filters have been clogged and tripped the safety stat on rear of appliance. Wash filters and replace stat Part No. 5432530

Remove all 3 filters, half moon filters below door, filter in door and heat exchanger from front of appliance and rinse under warm water dry and refit.

If start LED does not blink, most likely fault is your door lock.

If your circuit breaker is warm when it trips. Then you need to replace the breaker. Need to know how to use a meter also.

it sounds like it is the heating element which will be behind the back drum in front of the intake blower motor it may be disconnect or worn out make sure the it is unplugged before taking the machine appart very high voltage!

Clicca il link qui sotto per scaricare il manuale in Italiano:

Download italiano Libretto d'uso

Qui c'e anche la pagina di supporto Miele.

Non dimenticarti di votare adeguatamante la mia risposta, se questo ha risolto il problema vota blu, se ha aiutato blu, se non e' di aiuto giallo, il rosso e' per chi ti insulta.
Io direi che se cercavi il manuale qui il blu ci sta'.

Ciao, e in bocca al lupo con l'asciugatrice.

You should open the service panel and to find out where does the "beeping" unit located and to remove one of the wires connected to it (the unplugged wire should be insulated). Good luck!

The air flow problem is not the machine. There is probably a clog in the venting system in the house that needs to be cleaned out. When is the last time that was done?

One of the most common reasons is a faulty heating element. Over time, the heating element can malfunction and become unresponsive, causing the thermal safety mechanism to trip your circuit breaker as a safety measure. If this is the case, you might even hear beeping coming from the iron. The only solution here is to replace the element or replace the iron altogether, depending on the make and model of the iron. Another possible reason is an overloaded circuit. If you have too many electrical appliances plugged into one circuit, it can cause your circuit breaker to trip. Try unplugging some items from the circuit and see if that helps. If after this, you continue to have problems, an appliance repair technician is the alternative for a possible repair.

It sounds like your Miele T 494C Condenser Dryer may be experiencing an issue with the pump not functioning properly during hot cycles. It is likely that the pump is overheating and causing it to malfunction. One possible cause of this issue could be a clogged pump filter. Over time, lint and other debris can build up in the pump filter, reducing its efficiency and causing it to overheat. Cleaning or replacing the pump filter may resolve this issue. Another possible cause could be a malfunctioning thermostat that is not controlling the temperature correctly and causing the pump to overheat. If the pump is overheating, it could be caused by a malfunctioning thermostat, which would need to be replaced by a professional technician. It's also possible that the pump may be damaged or worn and needs to be replaced. It's recommended to consult the manufacturer's manual or contact the manufacturer's customer service for further assistance. They may be able to provide more specific troubleshooting steps or recommend a professional technician to repair the dryer. Keep in mind that attempting to repair a dryer can be dangerous if you're not familiar with the proper procedures and safety precautions. Regenerate response

There is help here for the various sensors https://www.google.com/search?q=Miele+Novotronic+T7644C+moisture+sensor ..

Everything should be off before the program starts and should stop at the end of the cycle. For oddities like that, you need Miele Service. They are all computer diagnosed on the engineer's laptop computer. Sounds like a control board issue, but hopefully can be reprogrammed.

it needs service badly, why delay and flood the home why"? call them in USA yp.com find home dryer service. and call. that is what 99.9999% do not. (not me y)

Sounds like you did a pretty good job. In my experience the blockages are in the rear machine vent, the tube, and just behind the external wall vent. You can even find the odd bird nest in there. Also make sure the flaps on the outside open fully and with ease.. Disassembly instructions https://www.google.com/search?q=miele+touchtronic+t1403+remove+front+panel ..

Page 58 of the service manual says 'No Gas Ignition'. You need a service call as it is GAS appliance. https://www.slideshare.net/avermapub/miele-gas-dryer-t9820-service-manual I couldn't find anything in normal searches. Code 98 is specific to that model. https://www.google.com/search?q=miele+dryer+error+code+98+fix .. ..

It is a condensing dryer, so the small pump is nearer the top than say a washing machine or dishwasher that has them positioned near the floor. Look on the rear for screws to remove the back panel. I would say it is an easy job.

There is a small component above the heating coil. It is your temp regulator. It is a small round component wired in line with everything. should only be two wires and easy to fix/replace yourself. You will need to get the part number off it or have the make and model when you go to get a replacement part for it.

Anything here that helps. In my experience Drum Seals are felt, Door Seals are rubber. https://www.google.com/search?q=Miele+Honeycomb+Dryer+T4224C+replace+drum+seal ..