20 Most Recent Craftsman 25cc 2-Cycle Gas Blower/Vac - Page 3 Questions & Answers

It would be a good idea to start by replacing the belts. In 20006 they made a DTL 3000 and this one... https://www.manualslib.com/manual/32322/Craftsman-18-5-Hp-917-273823.html The model # should be on a sticker under the seat. You can take the belts off and the shop can measure them too. Best to you.

As you mentioned, Craftsman chainsaws are often manufactured by Poulan, and they may share similar specifications with corresponding Poulan models. However, without specific documentation or further details, it's challenging to provide an exact RPM value for this particular model. To obtain accurate and reliable information about the nominal maximum RPM for the Craftsman chainsaw, I recommend referring to the owner's manual or contacting the manufacturer directly. They will be able to provide you with the precise specifications for this specific model.

Likely the unit is detecting a reverse direction. Could be the reverse switch, adjustment, or debris. Try using the ROS position on the ignition switch. If the problem goes away then it is definitely reverse operation related and further diagnosis of reverse detection required.

Clear the upper side of the mower deck of ALL debris. If this problem began just after a belt change, wrong belt.

I have the same rear engine tractor and cannot find parts anywhere. I did find another model that seems to look exactly the same. The model is 536.270212. It walked me through removing the deck, blade and motion belt. You can find the manual at www.hammerwall.com.. Hope this helps.

Caveats when using starter fluid.The carburetor must not flood the cylinder with fuel. A flooded engine will not fire, even on starter fluid. If you're not sure, pinch off the fuel line and drain the carburetor bowl. Remove the spark plug and pull recoil several times to dry out the cylinder.Remove air filter, set choke full open, spray a short burst of fluid directly into the carb throat. Promptly pull starter.Use a new dry spark plug. If it does not fire, try gapping plug 0.005" shorter and repeat above procedure.Comment for further assistance.

Question edited for clarity. I have removed all the information that isn't needed. Question moved from Cars and Trucks. The answer is the same as it was yesterday. All Ride on Mowers have a tensioner for the belt. Some have a spring operated idler pulley, some have bolts you slacken and physically move the drive pulley in tracks. One you have the belt correctly tensioned, you tighten the bolts. Look at the videos

The belt needs tensioning. Is the belt routing correct? https://www.google.com/search?q=craftsman+247.203750+belt+diagram

0.025in. (0.635 mm)

The location of the deck pins on your Craftsman T1200 riding lawn mower may vary depending on the specific model and year of your mower. However, here are some general steps you can follow to identify the correct location of the deck pins: 1. Examine the deck and the mower: Look for any markings or labels on the deck that indicate the location of the deck pins. Some mowers may have a decal on the deck that shows the correct placement of the pins. 2. Check the owner's manual: Refer to your owner's manual for specific instructions on how to install the deck and where the pins should be located. The manual should have diagrams or pictures that show the correct placement of the deck pins. 3. Use trial and error: If you're unable to find any markings or instructions, you may need to use a process of elimination to identify the correct location for the deck pins. Try inserting the pins in different holes and check to see if the deck is level and secure. If not, try a different combination of holes until the deck is properly secured. Keep in mind that it's important to ensure that the deck is properly installed and secured before operating the mower. If you're unsure about how to install the deck or where the pins should be located, it's best to consult a professional mechanic or contact Craftsman customer support for assistance.

Question edited for clarity. It is shown here https://www.justanswer.com/small-engine/bhlet-tried-repair-ignition-craftsman-zero-turn.html https://www.google.com/search?q=craftsman+247.25001+wiring+diagram ..

It could be due to: Fuel restriction Low engine compression / worn engine components Worn spark plug Plugged air filter

Question edited for clarity. Help in the link, but basically you follow the lever and linkages and tighten them up. https://www.google.com/search?q=craftsman+t-100+transmission+lever+loose Here are all the parts in a schematic diagram

T 100 (CMXGRAM201302) (13AC77XY093) - Craftsman ...

PartsTree https://www.partstree.com > models > t-100-cmxgram... Repair parts and diagrams for T 100 (CMXGRAM201302) (13AC77XY093) - Craftsman Lawn Tractor (2021) ....

Parts https://www.google.com/search?q=craftsman+944.604891+parts and manual https://www.manualslib.com/products/Craftsman-Lt2000-6034310.html ..

yes, once you have removed batteries. Good luck unit is most likely damaged from battery leakage.

You can find a copy of the owner's manual for your Craftsman riding lawn mower model 917.287130 on the Sears Parts Direct website. Here are the steps to find and download the manual:

1. Go to the Sears Parts Direct website at www.searspartsdirect.com.
2. Click on the "Manuals" tab at the top of the page.
3. In the "Search for Manuals" box, enter "917.287130" and click "Search".
4. Click on the "View Manual" button next to the "Owner's Manual" option.
5. You can now view the manual online or download it as a PDF by clicking on the "Download" button.

Note that you may need a PDF viewer, such as Adobe Acrobat Reader, to view the manual. If you have any issues downloading or viewing the manual, you can contact Sears Parts Direct customer service for assistance.

all the parts and diagrams are in the links https://www.google.com/search?q=craftsman+model+c950-52677+parts ..

The manual bypass valve lever on a Craftsman 247.288852 lawn tractor with an MTD 918-04566 fluid drive transmission is typically located on the rear of the transmission, near the pulley. You may need to remove the rear cover to access it. Look for a small lever or knob that can be turned or pulled to disengage the transmission and allow you to move the tractor manually. If you're having trouble locating the manual bypass valve lever, you may want to consult your owner's manual or contact the manufacturer or a qualified technician for assistance. They should be able to provide you with more specific information and guidance on how to locate and operate the manual bypass valve lever.

See owners manual. Free download at https://www.searspartsdirect.com/manual/223e1lwylt-000247/craftsman-917275820-front-engine-lawn-tractor-parts

no car told, makers,model, year. not one tiny clue told just a code# that code ,decodes to this 917294560 Craftsman Tiller so is not a car at all. it is a garden tool. answer buy the shop manual for it. pay ,