20 Most Recent HP OfficeJet D135 All-In-One InkJet Printer - Page 8 Questions & Answers

operator manual??


where you not provided with the oowners manual while buying?

You can't

Clean the copper contacts of the ink cartridge and the printhead wih the cotton swab and then try. Moreover in the printer there is an option to clean the printheads and ink carts. Later ty to print the h/w test page from the printer, if it prints fine then in the computer, righth click the printer icon and left click properties,in the color settings check if there is an option print in grayscale ... if thatoption is checked then uncheck the option.. and then print the test apge from the computer. If while priting the h/w test page it does not print in color then either upgrade the printer or replace the printer as the contacts of the printer ink carts slot are corrupted.

Make sure the printheads are not expired. Check the dates. Order new from HP direct I’m happy to help further over the phone at https://www.6ya.com/expert/jayw_0e86fb055a7b73de

Hi Jong,

Click on the web link given below and perform the steps as given in the web page.

This will fix the issue.

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00300221&cc=us&lc=en&dlc=en&product=64986

Good Luck.

Hi Sir.

The problem here is with the scanner bulb.
Please click on the web link given below and perform the steps as provided in the web page to get the issue fixed.

Here is the web link

http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00787271&cc=us&lc=en&dlc=en&product=64986

This will fix the issue else the scanner bulb is currupted.

To make sure that the problem is with scanner bulb.
Perform these steps.

Open the scanner lid and press copy button on the printer.
The scanner bulb should be lit and goes two and fro.
If this happens that means the scanner bulb is OK else Bad.

Hi Paula.

Please click on the web link given below to get the issue fixed.

The problem is with the scanner bulb.
However perform the steps given in the web page below.

http://h10025.www1.hp.com/ewfrf/wc/document?docname=bpu02549&cc=us&lc=en&dlc=en&product=64986

Click on the web link given below to get the issue fixed.

Hi Sproutman.

Please click on the web link given below and perform the steps provided in the web page to get the issue fixed.

http://h10025.www1.hp.com/ewfrf/wc/document?docname=bpu02549&cc=us&lc=en&dlc=en&product=64986

Click on the web link given above.

Scroll down to the error code and read the error code.

After working with the copier for over an hour, my husbband discovered quite by accident where the ink cartridge was located. It is inside on the left hand side, above the try that holds paper, and is next to impossible to see. It pulls out to the middle of the tray, and the cartridge can then be changed. Thank you so much for you time.
Sincerely,
Becky LaCour

All Heads needs to be replaced

lilman1,
it means you may have dialed the wrong number.
The fax machine your calling did not pick up. You can test the above by. Using your home phone or cell phone & call the fax number your trying to connect with. You'll know if it is a fax machine by the tone you hear.

You may have looked at this site. You haven't mentioned if you went to HP. Take a look at the link listed. This does include your OfficeJet D135. Post back if this all failed.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=bpa02107&cc=us&lc=en&dlc=en&product=64986&dlc=en&lang=en
map9966

1. Took out the color ink cart and clean the copper contacts of the ink cart with cotton swab, make sure that you do not touch the silver nozzle .
2. Try new ink color ink carts as someime this issue came up when the ink carts are about to finish up.
3. Replace the ink carts and do not us a refill ink.

New h/w found mesage will come up even if you will uninstall the usb printing suport from the deviece manager and reestart your computer with the same pinter so need not to worry. Moreover you need not to install the printer with other drivers, previous drivers can be used.
Regarding the step by step instructions to take apart the printers, that is with HP service centres and not available for all

Baud Rate is to lower the transmission speed of the fax, however these are the temp settings and once the power is off you have to reconfigure that. Follow the following steps :

From the front panel:

1. Press and hold the * key for 3 to 5 seconds until the display screen reads Test -001+ .
2. Enter in 620 on the key board, and press the Check Mark and the screen will read Cfg param id:

1. Enter the parameter ____ on the key board and press the Check Mark.

1. 159 - Receiving Fax baud rate

• 153 - Transmitting Fax baud rate

1. The screen will read Cfg param val: 26

1. Enter in the value ____ and then press the Check Mark .

1. 0 = V.17 14400

• 2 = V.17 9600
• 6 = V.29 9600
• 10 = V.27 2400

1. Screen will read Test -001+
2. Press the Reset button until you get back to Ready

Both the printer and the computer are machines and it solely depends upon the speed of the computer as to in how much time thye data is transmitted to the prinetr to print. Check the speed of the processor, RAM,USB port(if connected with usb cable), length of the usb cable /ethernet cable, distance of the router from the computer and the printer, size of the dcument/image.

Resolution for Lynne:
1. Unplug the power cable from the pwer strip and open the front door of the printer and move the carriage(in which the ink carts are connected) from the left to right and then back again for 2-3 times.
2. Plug in the pwer cabe and turn on the printer and print the h/w tets page.. if it prints fine, then try to, send and recieve a fax, If the carriage agains jams then replace the printer or serviec the printer.

Resolution For Stuart:
1. Th scrapping noise indicates that the ink carts are not inserted in the printer slot properly.
2. Pull the ink carts out and then push them back in and mak sure the printer should be on .
3. Clear the queue and then print the h/w test page, if prints fine then go ahead with fax.

There are two things that you can do...
Clean printheads, because of ink buildup, or clean the heads and contacts because of debris buildup.

1. Clean the printheads; this is done when there is streaking in the printout
1. Press Menu
2. Press 7 (Status Maintenance Menu)
3. then 2 (Clean Printheads)
   
4. Check print out. If it's still bad, then replace the printhead that's not working.
2. Clean the ink cartridge contacts
1. Using a clean lint-free cloth, distilled or filtered water (no tap water)
2. Open the print-cartridge access door
3. After cartridges are in center, unplug unit
4. Remove the cartridges
5. Examine contacts for debris buildup
6. With damp cloth clean any debris buildup on cartridge or in cartridge bed
7. Repeat for others
8. Replace all and turn on printer
9. Message will appear to Re-align heads, press enter to do this

If this helped, please rate FixYa!, ThankYa!

You will need to re-install the drivers. Try using the CD that came with it. I'm sorry but I don't have any experience taking apart printers.

take out the printer heads and clean.