20 Most Recent HP Officejet 4110 All-In-One InkJet Printer - Page 5 Questions & Answers

You may try the following suggestions:

• While it says offline, right click the printer icon and cancel print jobs.
• Right click the icon again, then 'Set Printer Online'.
• Power cycle the printer. Just turn it off and then turn it back.
• Reinstall the printer by running the 'Add Printer Wizard' and let it automatically find your printer to be reinstalled.

No but you can share it from the computer it is hooked up to. here is an article that will provide the information for you to setup sharing your printer http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

there is no way u can go to the scanner bulb .if u try to do that u can break the scanner glass. so just call hp tech support . they will upgrade the printer for u .

Your colour cartridge must print OK for alignment complete.Try to change it.

The scan button on the printer is to scan to PC and then save it to computer and then print it.

Steps for scanning from Computer.

Windows Vista:

1. Click the Start (Windows) icon.
2. Click All Programs.
3. Click Windows Photo Gallery.
4. Click File and then click Import From Scanner or Camera.
5. Click Import.
6. Click Scan

Windows XP.

=== Scanning with Paint: ===

1. Click the Start (Windows) icon.
2. Click All Programs.
3. Click Accessories.
4. Click Paint.
5. Click File and then click From Scanner or Camera.
6. Click Scan.

you have not installed the printer at your PC.pls installed the printer.

Hello,

What I am going to say may not be relevant to your case, but a scanner needs to scan to some image format( a default format or one you select. So you computer needs to have some kind of imaging software installed.

Apparently, the only kind of imaging software the scanner detects is Windows Paint.

If this is really the case, go to the Internet and download some free imaging software: IRFANVIEW, or The Gimp.

Hope it helps

Do you have any Digital Answering Machines in the house?
or is it a dedicated line?
anyway heres the link for the 3 digit error codes document, its a public document that can be found by searching www.hp.com using this Article #: bpu02549 or buu02549
anyway as you can see 388 result/solution is the following...

Problem: Unable to complete the connection.
Solution: *Reattempt the fax reception at a different time when telephone line conditions have improved.

Now this means that one or both fax machines can have a problem. So lets isolate the problem.

Place a regular phone into the wall jack that the OJ 4110, if there is a static sound then its the phone line that is having the problem. if there is no static continue on...*Note if you have a DSL Internet service you NEED a filter for the fax*
..
What this is most commonly caused by is Bad line conditions which can occur in some different ways.
1) If there has been recently a Thunder Storm the electrostatic discharges interupt phone signals.
2) Recent power line downage
3) Recent Phone line downage
4) The phone company upgrading the lines

But basically something is BLOCKING the faxes from hearing each other. That is why you get this error code.
You can call your phone company to run a line trace. The reason you want to do this is so that you can eliminate the possibly of Static, Yes there are differnt types of it;
1) the normal static that you and me can hear
2) the SuperSonic Static, AKA Static in the Higher Frequency Ranges, where your DSL internet connection is. the Fax will pick up on those Higher frequency ranges, and it will cause problems. So put a DSL Filter on the Fax it wont hurt, and most of the times it helps alot.
Again Make sure ECM is disabled.
other than that, try unplugging all devices on the phone system an try...
i think there is alot fo information, i cant think of anything else...
Hope that helps

what kind of connection you are using, I ment broadband or some other

does it try to pull the paper? if doesn't check the paper sensor, if it does try to pull, you need to clean very well the "pick-up" and the under part. Try using "Thinner", it's very good!

Hope it work now.

please proceed as per the following instructions...

, without turning off your printer, unplug the power cable from the unit, after you have done that, on your printer, hold the Ok and cancel button to gether and while you are holding it down, plug the power cord back and keep holding the buttons for about 5 sec.
once the unit turns off, use the power button and turn it on. the unit would print and alignment sheet and this should fix the issue

if that doesnt help....

The ADF paper sensor is misplaced. Follow these steps below to correct the position of the ADF sensor.

1. Open the document feeder cover, which is on the left side of the ADF, when standing in front of the unit.
2. Locate the black plastic ADF paper sensor on the inside of the cover door.
3. If the sensor is loose on one side, reattach the sensor in the small hole. See the images below.
   Figure 1: ADF paper sensor is loose Figure 2: ADF paper sensor is attached
   
   beyond this ur only option wud be to call up HP as it could be a serious hardware issue....
   regardsiversh

1. Open a document in the program being used to print.
2. Click File , click Print , and then click Properties . The product Properties dialog box appears.
3. Click the Paper/Quality tab.
4. Choose the appropriate paper size from the Size is drop-down menu.
5. Choose the appropriate paper type from the Type is drop-down menu.
6. Click OK and then click OK again to print the document..

You have not mentioned the exact problem.

You may reinstall the driver and that should fix most of the problems.
ftp://ftp.hp.com/pub/softlib/software3/COL6316/mp-19447-3/rw2_021_w02_enu.exe

ok that fine.if simple problem. firstly remove ur printer software from ur pc. for it go to control panel and click add/remove icon. then uninstall ur driver software. after that u should install ur printer software. then become ok

please you got to printer preferences select it then show a manu you select color select print in color and print if you are not succed you change a color cartridge

Check that you haven't increased the printing resolution beyond what is sufficient to print your document.

High resolution vs. draft output will cause you to use a lot more ink and will take at least twice as long to print a page because it is likely printing each line at least twice. This is how full color (photo quality) images are printed. If you don't need a photo to be dark, then set your printer to "Standard" or "Draft" settings.

go to google and specify the details about the printer version,name and then search for the driver