Top 20 Russell Hobbs 18276 Allure 1.5l Jug Blender 12 Speed 800w Questions & Answers

I also needed a seal - contacted Russell Hobbs - told that product is discontinued - they do not hold stock on the seal. Great service !!

It makes cold soups like Gazpacho and Vichyssoise, so make sure the heating / cooking function is set. If it is, ask Russel Hobbs where your local service centre is to diagnose and replace the element. https://www.google.com/search?q=Russell+Hobbs+soup+maker ..

Sometimes it is a seized shaft, does the blade turn by hand? It could be the motor has failed, or the start capacitor on the motor. It could be the electronics. There's a safety lock built into the handle of the jug. If the jug cover doesn't key into the lock properly, the motor base won't start. https://www.google.com/search?q=Russell+Hobbs+RHB315+Blender+not+working ..

Check continuity of the power cable. Contacts of the power switch. Carbon brush of the motor.

if you can not find a switch to replace the bad then buy a new blender

Overheating normally. It should reset. If it doesn't it is probably time for a new one.

Hi there... firstly is this blender a USA or UK model and do you have a Multimeter handy? if you can remove the fuse from the plug (UK only) and test t through diode mode on a multimeter or Continuity test across the fuse terminals... if it beeps the fuse is good if nothing the fuse is blown we can move on from there

Using https://www.google.com I searched the internet and found the following lInk to a possibly similar free manual: https://www.manualslib.com/manual/785919/Russell-Hobbs-Simply-Smoothie.html

There is no such button, most likely the motor has failed.

Your best bet is to open it up carefully and investigate. It's usually a minor problem unless it is old. Check it out yourself, you can't break something that's already broken and you'll gain some knowledge! :D

Check to be sure your rubber gasket is clean and in the proper place which should be between the jug and the blade asembly. Also I have seen leaking when the assembly was tightened too much. If you still have your receipt etc you may be able to exchange the unit where you purchased it. Alternatively contact the manufacturer and see if they can replace under warrenty

Knob on top push

I'm afraid I can't answer this, but am posting to say I've just discovered exactly the same problem with my newly-purchased blender - same model - and have contacted Russell Hobbs service department to find out if I'm doing anything wrong (i'm sure I'm not!). I'll post any response here.

go to culinaryparts.com you can probably order one

Contact the manufacturer. It's probably still under warranty

Question edited for clarity. Question moved from Washing Machines category to Blenders. Something to do with the Outlet and Soy Milk! :>D https://www.amazon.com/gp/customer-reviews/R3S2NMMMKVYCV8?ASIN=B09L7PXN1B https://www.google.com/search?q=joyoung+a+super+power+blender+e08+error ..

Direct or from eBay https://www.google.com/search?q=Kitchen+Aid+Model+KHB300+hand+held+blender+parts ..

Question edited for clarity. That is likely a failed heating element, failed thermostat, or worse case scenario, a failed control board. https://www.google.com/search?q=prolectrix+soup+maker+not+heating+up ..

the lock/unlock button on the Cuisinart Smart Stick CSB-75 blender may not stay locked when pressed in. The solution is to hold the blender in the palm of your dominant hand, press the low or high button and hold, then push and release the lock button on top with a finger on your other hand. The blender motor should start as soon as you push the lock button down and stay running until you release the high or low button. However, fix.com offers OEM Black and Decker blender parts and accessories, including rubber gaskets, jar bases, measuring cup lid inserts, and blade assemblies. You may want to check if the parts you need are available and replaceable. If you are unable to repair the blender yourself, you can contact Black and Decker customer service for assistance. They may be able to provide you with additional information on how to repair your blender or direct you to a local repair shop.

Question edited for clarity. It appears to be an eBay special. you may be able to buy using the diameter. Shops that sell fasteners sell O-rings, but this is likely wider, so more a gasket. https://www.google.com/search?q=GNC+Live+Well+Blender+BL3340+replacement+O-ring https://www.google.com/search?q=GNC+Live+Well+Blender+BL3340+replacement+gasket ..