Russell Hobbs 14863 Steam Station [Kitchen & Home] - Answered Questions & Fixed issues


Hi there...

firstly is this blender a USA or UK model and do you have a Multimeter handy?

if you can remove the fuse from the plug (UK only) and test t through diode mode on a multimeter or Continuity test across the fuse terminals... if it beeps the fuse is good if nothing the fuse is blown

we can move on from there

Russell Hobbs... | Answered on Jul 22, 2020 | 60 views


Using https://www.google.com I searched the internet and found the following lInk to a possibly similar free manual:

https://www.manualslib.com/manual/785919/Russell-Hobbs-Simply-Smoothie.html

Russell Hobbs... | Answered on Jun 07, 2020 | 37 views


There is no such button, most likely the motor has failed.

Russell Hobbs... | Answered on Jan 12, 2017 | 531 views


Your best bet is to open it up carefully and investigate. It's usually a minor problem unless it is old. Check it out yourself, you can't break something that's already broken and you'll gain some knowledge! :D

Russell Hobbs... | Answered on Apr 08, 2016 | 187 views


Check to be sure your rubber gasket is clean and in the proper place which should be between the jug and the blade asembly. Also I have seen leaking when the assembly was tightened too much.

If you still have your receipt etc you may be able to exchange the unit where you purchased it. Alternatively contact the manufacturer and see if they can replace under warrenty

Russell Hobbs... | Answered on Oct 06, 2015 | 224 views


Knob on top push

Russell Hobbs... | Answered on Jun 19, 2014 | 140 views


I'm afraid I can't answer this, but am posting to say I've just discovered exactly the same problem with my newly-purchased blender - same model - and have contacted Russell Hobbs service department to find out if I'm doing anything wrong (i'm sure I'm not!). I'll post any response here.

Russell Hobbs... | Answered on Jan 12, 2011 | 475 views


go to culinaryparts.com you can probably order one

Russell Hobbs... | Answered on Feb 11, 2010 | 147 views


Contact the manufacturer. It's probably still under warranty

Russell Hobbs... | Answered on Sep 23, 2009 | 716 views


This problem can come from both the blender and or even the circuit powering it. First make sure that the outlet you have your blender plugged into is powered and not ripped If your blender still is not turning on then you may have a faulty motor or motor connection. Or the fuse could be blown and needs to be replaced.Or it could also be jamming for this you must first need to disassemble the drive and then turn the blade shaft. If it seems to be stuck or jammed here check what is the causing it to be jamming. In most of the cases it is debris that are stuck in the blades of the blender that causes it to be stuck.

Blenders | Answered on Nov 30, 2020 | 12 views


https://www.amazon.co.uk/Gordon-Ramsay-Cooks-600w-Blender/dp/B003UTUO2M

Blenders | Answered on Nov 20, 2020 | 48 views


The blades may not be turning because the blade assembly is not fully tightened onto the blender bottle. Another reason could be that you are not putting the blender bottle and blade assembly into the blender base in the proper way. For more answers visit the Oster Blend-N-Go My Blend troubleshooting page: Oster Blend-N-Go My Blend Troubleshooting

Blenders | Answered on Nov 20, 2020 | 54 views


https://youtu.be/dklwnGPwHVw

Blenders | Answered on Nov 20, 2020 | 14 views


The shaft has probably become tight in the bearings and the assembly will need to be dismantled for cleaning and possibly lubrication - I am unfamiliar with the Ninja but the average blender is a fairly basic mechanism and not many fasteners have to be removed before the parts needing attention either fall off or can be removed. It is a fairly intuitive process for the handy person.

You could perhaps start with the nut on the blade - there seems enough exposed thread to judge whether it is left or right hand thread and it shouldn't be particularly tight. Lots of cloth should be used when holding the blade...

Blenders | Answered on Nov 14, 2020 | 13 views


The thermal fuse must be in intimate contact with the motor so when the motor temperature climbs dangerously high the fuse temperature doesn't lag far behind.

I have seen the thermal fuse buried in the windings of a transformer so it isn't beyond the realms of possibility it could be inside the motor. The thermal fuse body is metal and live and so must be insulated and so is generally found in the supply wire inside some heat resistant sleeving strapped firmly to the motor...

Blenders | Answered on Aug 09, 2020 | 18 views


try rotating the container part 1/4 of a turn to line up slots and press down . then if it does not blend turn another 1/4 turn to line up slots and press down pushing container into base motor unit .
container and screw on blade lid is put in upside down and the plastic posts have to match the base unit to turn on the blender when you press down on container into base unit.

I own and use a ninja blender !.

Blenders | Answered on Jul 04, 2020 | 1,647 views


https://youtu.be/i5E-t09PFL4
watch this video

Blenders | Answered on May 05, 2020 | 166 views


you checked at your nearest electronic shop,I think the motor available in that shop

Blenders | Answered on May 05, 2020 | 145 views


https://youtu.be/i5E-t09PFL4
you watch this video & your problem is solved

Blenders | Answered on May 05, 2020 | 154 views

Not finding what you are looking for?
Russell Hobbs 14863 Steam Station [Kitchen & Home] Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top Russell Hobbs Blenders Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

ray gallant

Level 3 Expert

70853 Answers

Tom Chichester

Level 3 Expert

60366 Answers

Are you a Russell Hobbs Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...