Top 20 Russell Hobbs 14863 Steam Station [Kitchen & Home] Questions & Answers


Hi there...

firstly is this blender a USA or UK model and do you have a Multimeter handy?

if you can remove the fuse from the plug (UK only) and test t through diode mode on a multimeter or Continuity test across the fuse terminals... if it beeps the fuse is good if nothing the fuse is blown

we can move on from there

Russell Hobbs... | 59 views | 0 helpful votes


Using https://www.google.com I searched the internet and found the following lInk to a possibly similar free manual:

https://www.manualslib.com/manual/785919/Russell-Hobbs-Simply-Smoothie.html

Russell Hobbs... | 36 views | 0 helpful votes


There is no such button, most likely the motor has failed.

Russell Hobbs... | 530 views | 0 helpful votes


Your best bet is to open it up carefully and investigate. It's usually a minor problem unless it is old. Check it out yourself, you can't break something that's already broken and you'll gain some knowledge! :D

Russell Hobbs... | 187 views | 1 helpful votes


Check to be sure your rubber gasket is clean and in the proper place which should be between the jug and the blade asembly. Also I have seen leaking when the assembly was tightened too much.

If you still have your receipt etc you may be able to exchange the unit where you purchased it. Alternatively contact the manufacturer and see if they can replace under warrenty

Russell Hobbs... | 224 views | 0 helpful votes


Knob on top push

Russell Hobbs... | 140 views | 0 helpful votes


I'm afraid I can't answer this, but am posting to say I've just discovered exactly the same problem with my newly-purchased blender - same model - and have contacted Russell Hobbs service department to find out if I'm doing anything wrong (i'm sure I'm not!). I'll post any response here.

Russell Hobbs... | 475 views | 1 helpful votes


go to culinaryparts.com you can probably order one

Russell Hobbs... | 147 views | 0 helpful votes


Contact the manufacturer. It's probably still under warranty

Russell Hobbs... | 715 views | 0 helpful votes


https://youtu.be/dklwnGPwHVw

Blenders | 13 views | 0 helpful votes


The thermal fuse must be in intimate contact with the motor so when the motor temperature climbs dangerously high the fuse temperature doesn't lag far behind.

I have seen the thermal fuse buried in the windings of a transformer so it isn't beyond the realms of possibility it could be inside the motor. The thermal fuse body is metal and live and so must be insulated and so is generally found in the supply wire inside some heat resistant sleeving strapped firmly to the motor...

Blenders | 17 views | 0 helpful votes


The shaft has probably become tight in the bearings and the assembly will need to be dismantled for cleaning and possibly lubrication - I am unfamiliar with the Ninja but the average blender is a fairly basic mechanism and not many fasteners have to be removed before the parts needing attention either fall off or can be removed. It is a fairly intuitive process for the handy person.

You could perhaps start with the nut on the blade - there seems enough exposed thread to judge whether it is left or right hand thread and it shouldn't be particularly tight. Lots of cloth should be used when holding the blade...

Blenders | 13 views | 1 helpful votes


The blades may not be turning because the blade assembly is not fully tightened onto the blender bottle. Another reason could be that you are not putting the blender bottle and blade assembly into the blender base in the proper way. For more answers visit the Oster Blend-N-Go My Blend troubleshooting page: Oster Blend-N-Go My Blend Troubleshooting

Blenders | 54 views | 1 helpful votes


https://www.amazon.co.uk/Gordon-Ramsay-Cooks-600w-Blender/dp/B003UTUO2M

Blenders | 48 views | 0 helpful votes


so order one fixya doesnt sell products

Blenders | 66 views | 0 helpful votes


fixya doesnt sell products

Blenders | 67 views | 2 helpful votes


Hello, Rebecca -

Please see my reply here: https://www.fixya.com/answer/answerpageslideview.aspx?thid=29753915&ctg=142&brd=3705

Best wishes.

Blenders | 99 views | 1 helpful votes


https://youtu.be/i5E-t09PFL4
you watch this video & your problem is solved

Blenders | 154 views | 0 helpful votes

Not finding what you are looking for?
Russell Hobbs 14863 Steam Station [Kitchen & Home] Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top Russell Hobbs Blenders Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

ray gallant

Level 3 Expert

70663 Answers

Tom Chichester

Level 3 Expert

60169 Answers

Are you a Russell Hobbs Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Russell Hobbs Blenders

  • Russell Hobbs Blenders

Most Popular Question

fix blender

  • Blenders
Loading...