20 Most Recent Roper RAB2121KW Top Load Washer Questions & Answers

0helpful
2answers

Agitator not spining properly to pull clothes down into water

remove agitator cap remove boplastic cover underneath remove bolt remove upper portion of agitator replace agitator dogs part # 80040
12/26/2016 5:50:10 PM • Roper RAB2121KW... • Answered on Dec 26, 2016
0helpful
1answer

Whining on spin cycle

There could be something in the pump .If you can tip the machine back and remove the belt try to spin the pump pulley by hand if you hear the noise that's it if not call for service.
9/28/2015 5:30:32 PM • Roper RAB2121KW... • Answered on Sep 28, 2015
0helpful
1answer

FILL CAPACITY

your machine has a pressure switch to tell it what the water level is-if it is overfilling make sure the small hose attached to the tub is not clogged-it may even be the fitting it attaches to is clogged-what ever you do don't give up your old machine-the new ones won't last as long or wash your clothes as good-cheers Denny
10/26/2013 7:56:20 PM • Roper RAB2121KW... • Answered on Oct 26, 2013
0helpful
1answer

Does the back cover come off a roper washer to

In a word, NO! Watch the video before proceeding or you will have a mess! :-)

Repair Video

Kelly
5/25/2011 1:17:34 AM • Roper RAB2121KW... • Answered on May 25, 2011
0helpful
1answer

Kenmore Washer, 70 Series, Model 110-26712690, Spin Cycle Problem

I had the same problem as most of you dosnt spin right or adgitate especially with heaver loads.

Theres a coupler which acts like a universal joint on a car. Its made of plastic and the plastic numbs that lock it in break off. I changed my coupler and that was 2 years ago and havent had any problems since.
5/15/2011 8:51:10 PM • Roper RAB2121KW... • Answered on May 15, 2011
0helpful
1answer

My machine is leaking from a white plastic piece

does it look like this? somewhat challenging to replace because of the washer cabinet, if you don't put it back correctly then the washer will move around when it goes into spin. go to the you tube link.

fgonzalez278.jpg
3/10/2011 8:13:03 PM • Roper RAB2121KW... • Answered on Mar 10, 2011
0helpful
1answer

My washer does not spin

replace clutch partimage.aspx?imgid=z3bqljbfbxnfntg3ntgyl0xqvy9zb3rvahb0cmfwlw%3d%3d
1/10/2011 10:58:18 PM • Roper RAB2121KW... • Answered on Jan 10, 2011
0helpful
1answer

Kenmore 90 series washer is starting to not spin

It appears your clutch assembly has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
10/1/2010 1:15:42 AM • Roper RAB2121KW... • Answered on Oct 01, 2010
0helpful
1answer

My kenmore top loading washer will not spin

It appears your timer/main controller/CCU has failed in this instance.

For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...


FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.


If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.


Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.




Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question&%$#
9/30/2010 11:46:31 PM • Roper RAB2121KW... • Answered on Sep 30, 2010
0helpful
2answers

Washing maching not filling with water

The problem is most likely the water fill sensor switch. If it is telling the machine that it is full, it will go right to agitate.
8/30/2010 11:59:21 AM • Roper RAB2121KW... • Answered on Aug 30, 2010
0helpful
1answer

Not spinning

Hi,
If you are having a problem with your top load washer then check out this tip...

Washing Machine2_bing.gif does not Pump or Spin
http://www.fixya.com/support/r4617986-washing_machine_not_pump_or_spin

If you are having problems with your front load washing machine2_bing.gif then checkout this tip...

Front Load Washing Machine2_bing.gif not draining and or not spinning
http://www.fixya.com/support/r4784376-front_load_washing_machine_not_draining

heatman101
6/18/2010 3:44:27 AM • Roper RAB2121KW... • Answered on Jun 18, 2010
0helpful
1answer

I have a kenmore washer and when it is on the

If the washer agitates in the wash cycle but not in the rinse cycle, my best guess is that the timer is bad. They are not too hard to replace if you can get one from sears, but make sure you unplug the washer before you reach in to the electrical stuff. On my washer, the control panel on top had a back plate that was held on by a few screws. Best of Luck
3/9/2010 11:57:45 PM • Roper RAB2121KW... • Answered on Mar 09, 2010
0helpful
1answer

Why does my washer leaks every often when it

You will never know until you take the body off, jumper the lid swich and run a cycle. I have repair photos HERE If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61
3/1/2010 12:46:26 AM • Roper RAB2121KW... • Answered on Mar 01, 2010
0helpful
1answer

Someone know this item equator ez3600 all in one

Yes, the equator EZ3600 is a combo washer dryer, which washes and dries in one unit.
2/25/2010 7:08:27 PM • Roper RAB2121KW... • Answered on Feb 25, 2010
0helpful
1answer

Will not drain or spin

there is a chance that your lid switch is faulty.you can also check to see if there is anything obstructing the drain pump
1/31/2010 6:13:46 AM • Roper RAB2121KW... • Answered on Jan 31, 2010
0helpful
1answer

Timer makes continuous whirring noise

Timer needs replaced.
1/9/2010 12:05:44 AM • Roper RAB2121KW... • Answered on Jan 09, 2010
0helpful
1answer

Starts, but does not move on through cycles

check your lid switch may be broken. or could be your timer does it stop and not advance? if it gets stuck you more than likey have a broken lid switch. but if it gets stuck in one cycle and keeps washing and washing and washing you more have a bad timer.
1/5/2010 4:59:49 AM • Roper RAB2121KW... • Answered on Jan 05, 2010
0helpful
1answer

Roper heavy duty washing machine won't drain suds

i had one of these, and also had the same issue. When I did a load no problem. When my flatmate did a load is when the suds issue occurred. Make sure you are using the right amount of soap for the water level
12/27/2009 6:08:07 PM • Roper RAB2121KW... • Answered on Dec 27, 2009
0helpful
1answer

Washer wont drain just stops when it gets to this

If the washer fills, agitates, then stops at the rinse and won't drain, or if the washer does an initial fill, then stops, this is a symptom of a lid switch malfunction.

The following link explains how to access and/or replace one:

http://www.fixya.com/support/r385198-replacing_lid_switch

The lid switch is usually mounted under the washer top casing, on the right hand side on most top load models. It is activated by a plastic piece on the lid (called a "Lid Strike") through a small hole on the rim of the wash tub opening. In many cases the lid strike breaks off the lid, or the lid switch becomes loose and no longer makes contact. Inspect the lid to make sure the lid strike is still intact, and then inspect the mounting screws (adjacent to the small opening on the wash tub rim) and make sure they are snug.

If the model number you have this listed under is correct, the part number for a replacement lid switch is 3949247. This is a very simple repair, that usually costs about $30 to repair yourself.

Appliancepartspros.com, pcappliancerepair.com and searspartsdirect.com usually have excellent exploded view diagrams of what I am referring to. Just type in your model number and look under the "Top and Cabinet Parts" section. The lid switch is listed as item 11 and the lid strike is listed as item 20.

If you have questions, or require additional assistance, please let me know. Post back with a correct model number if the model number is not correct. I hope this helps you.
10/2/2009 1:39:38 PM • Roper RAB2121KW... • Answered on Oct 02, 2009
Not finding what you are looking for?
Roper RAB2121KW Top Load Washer Logo

Popular Tags

75 questions posted

Ask a Question

Usually answered in minutes!

Top Roper Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

Mike

Level 3 Expert

4383 Answers

Brad Brown

Level 3 Expert

19165 Answers

Are you a Roper Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Roper Washing Machines

  • Roper Washing Machines

Most Popular Question

kenmore washer when

  • Washing Machines
Loading...