20 Most Recent Roper RAS6233KQ Top Load Washer Questions & Answers

0helpful
1answer

We have a Roper 7

most likely needs new lid switch assy.
5/8/2017 12:43:07 PM • Roper RAS6233KQ... • Answered on May 08, 2017
0helpful
1answer

Washer won't start/fill/spin -- anything

Dea, does the washer fill? If it fills and justs sits there it could be the pressure switch. If it fills, agitates and then no spin no drain, then it's the lid switch. If it doesn't do any of the above, it may be a timer issue. Lift the lid and gently lower it, do you hear a click when the actuator on the lid hits the switch? I will attempt to attach a picture on how the consol flips up to see the lid switch harness, pressure switch and timer. Your model will have two screws that must be removed, they maybe in back of the end caps. To remove the lid switch unclip the clips on the right and left side, unplug the harness and tip the cabinet foward. You will see how the lid switch mounts to the cab. Catriver..post back
4/30/2017 10:11:10 PM • Roper RAS6233KQ... • Answered on Apr 30, 2017
0helpful
3answers

The water pump started leaking and I just want to replace it. I can't figure out how to remove it.

I hope this information may help.
copy n paste

http://www.partselect.com/MultiModels.aspx?ModelNum=RAS6233KQ&searchTerm=img_FOU23FEA&RefineSearch=0&imgMfg=Whirlpool&Page=4

1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamps.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes

"Was this helpful?" YOUR RATEING is very important.thank you
7/22/2015 6:41:59 AM • Roper RAS6233KQ... • Answered on Jul 22, 2015
0helpful
1answer

Roper top loader direct drive washing machine vibration on spin

the counter weights inside gone bad or u need to balance the machine legs , use a leveler to check balance
3/9/2015 6:56:42 PM • Roper RAS6233KQ... • Answered on Mar 09, 2015
0helpful
2answers

Leaks when the washergoes into the spin cycle.

Could be crack on underhose or possible drum fault
8/12/2014 3:49:31 PM • Roper RAS6233KQ... • Answered on Aug 12, 2014
0helpful
1answer

Only cycle that works is the spin cycle

Defective timer seem far more likely.
5/13/2014 3:35:51 AM • Roper RAS6233KQ... • Answered on May 13, 2014
0helpful
1answer

My washing machine won't stop-

sounds like you blown the timer replacement?
5/13/2014 1:50:49 AM • Roper RAS6233KQ... • Answered on May 13, 2014
0helpful
1answer

RTW4640YQ0 made horrible loud noise banging so I

There are several springs in the machine and it sounds like one of them that you cannot see has broken. To get an idea about the problem, drain the machine and unhook it, lay it down so that you can see what is going on from the bottom of it.
11/4/2013 10:09:40 PM • Roper RAS6233KQ... • Answered on Nov 04, 2013
Not finding what you are looking for?
Roper RAS6233KQ Top Load Washer Logo

301 questions posted

Ask a Question

Usually answered in minutes!

Top Roper Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Mike

Level 3 Expert

4379 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Are you a Roper Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Roper Washing Machines

  • Roper Washing Machines

Most Popular Question

rtw4640yq0 made horrible loud noise

  • Washing Machines
Loading...