Top 20 Kenmore HE2 Plus 3.6 cu. ft. Super Capacity Front Load Washer Questions & Answers

0helpful
1answer

He2 washer wont drain. easy fix?

chjeck the pump for any blogg
6/5/2014 2:08:02 PM • Kenmore HE2 Plus... • 73 views • 0 helpful votes
0helpful
1answer

Kenmore front loader washer powers on but lets no water in

If the door lock is engaging, then there could be a few things causing the problem. These things are as follows:1) The water valve is bad - you can check this by seeing if when you turn the machine on if power, 115vac is being applied to it. If so the valve is bad, if not read forward.2) There is a part called the pressure switch, it controls the amount of water that flows into the machine. Its connected to the drum by a 1/4" tubing. You'll need to check to make sure that nothing is obstructing the tube.3) Take the bottom of the machine off, called the kick plate. Inside there is a tech sheet with diagnostic walk through's that will carry you the rest of the way If you need further help, I’m available over the phone at https://www.6ya.com/expert/jason_4570d45317834dd3
6/17/2012 6:23:39 AM • Kenmore HE2 Plus... • 96 views • 1 helpful votes
0helpful
1answer

Leaky drain hose

https://www.youtube.com/results?search_query=replacing+model+110.4756+drain+hose. click on this link and review numerous videos you find there and although you might not find your exact model you will find enough info to do your replacement
1/15/2018 5:48:03 PM • Kenmore HE2... • 83 views • 0 helpful votes
0helpful
1answer

I have an HE2 Model 110.47571601. The power will

There are two control boards (parts 3 and 6) shown here: http://www.searspartsdirect.com/model-number/11047571601/0582/0153200.html . Make sure to look at the Control Panel diagram. Part 3 is http://www.searspartsdirect.com/part-number/8540490/0026/110.html?modelNumber=11047571601&categoryName=Residential%20Washers&brandName=KENMORE . Part 6 is http://www.searspartsdirect.com/part-number/W10022320/0026/110.html?modelNumber=11047571601&categoryName=Residential%20Washers&brandName=KENMORE . With these part numbers, you should be able to find them online. They will be listed as Whirlpool or Whirlpool OEM parts. If you add a comment with the problem that led you to have a technician look at the washer, I will confirm which board is which. I suspect part 6 is the B board but I'm not certain of that. I hope this helps. Cindy Wells
4/20/2017 9:33:03 PM • Kenmore HE2... • 153 views • 0 helpful votes
0helpful
1answer

I replaced the drain pump and now if I try to start machine all I here is drain pump humming. It wont fill or cycle. still have a F21 code

Have you looked into the water level gauge? It may be stuck
6/24/2015 10:40:23 PM • Kenmore HE2... • 93 views • 0 helpful votes
0helpful
1answer
0helpful
1answer

Kenmore HE2T front loading washer. Will not start cycle... hums, and then turns off. no error codes given.

make sure the water is turned on to the unit.
12/7/2014 6:31:59 PM • Kenmore HE2... • 290 views • 0 helpful votes
0helpful
1answer

Have an HE2 washer. close door, select any cycle, press start, locks up then unlocks and shuts off???

unplug--see if it resets--if not--the control box is bad--about 300 for the part Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/david_2f6e03df6c124197
1/11/2015 10:58:15 PM • Kenmore HE2... • 86 views • 1 helpful votes
0helpful
1answer

Washer machine shakes when it spins and sounds like a helicopter landing- is not out of balance- and is leveled

sounds very like the bearing are gone i am afraid not good news its quite expensive to replace them if your machine is splitable
10/14/2014 3:41:49 PM • Kenmore HE2... • 195 views • 0 helpful votes
0helpful
1answer

Kenmore washer error codes

Appliance Repair Forums Near top of page click on Thread "HE Error Codes" Even blonde can do it Quick fix repair for Kenmore He2 front loading... Search youtube for he2 washer for other help videos
8/18/2014 3:29:58 AM • Kenmore HE2... • 565 views • 0 helpful votes
0helpful
1answer

Wash Cycle will not start; add garment and door locked lights on.

IF you take the panel off the is below the door, there is a drain plug and you should take it out. YOU will get lots of WATER. Be ready. Clean this out and try again. The issue is most likely the water solenoid valve is bad or the board that controls it is bad. You can also find the tech sheet when you look for the drain. It has all the tests that you can run.
2/1/2014 12:36:31 AM • Kenmore HE2... • 5,207 views • 1 helpful votes
0helpful
1answer

Flashing prewash and add garment lights

I have not got a sol yet.
12/16/2013 5:52:33 PM • Kenmore HE2... • 748 views • 0 helpful votes
0helpful
1answer

Washing machine not draining, LD error code

Through the lower tube of the tub may be able to remove the item of clothing.
12/22/2013 1:10:32 AM • Kenmore HE2... • 74 views • 0 helpful votes
0helpful
1answer

Error code f-28

F28 means your washer is locked and not unlocking. To unlock your washer take off the bottom access panel by removing the 3 bottom screws. Reach up near the latching assembly & attached to the door latch is a little plastic pull lever. Pull down on this lever and open the door. Unplug your washer for 60 seconds and plug your washer back in. If the error re-occurs you need to replace your door lock.Click if helped.
4/30/2013 7:14:06 PM • Kenmore HE2... • 260 views • 0 helpful votes
0helpful
1answer

Washer wont start

It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows though the inlet then the flow pressure should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Check this link to replace the inlet valve: http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

1/11/2013 10:54:39 PM • Kenmore HE2... • 40 views • 0 helpful votes
0helpful
1answer

Where can I find a diagram of the pump motor

see the videos test: God bless youhttp://www.youtube.com/watch?v=ScdWxXlIsFE&feature=results_main&playnext=1&list=PL8BA631872A967A88God bless you
6/28/2012 11:21:09 PM • Kenmore HE2... • 30 views • 0 helpful votes
0helpful
1answer

My kenmore he2 wont dispence the soap in the soap dispencer

Evening to youAllow the washer to start a cycle and have the dispenser drawer ajar and observe through which dispenser the water goes.Does the first stream go through the pre-wash dispencer,secondly notice where the main stream goes and lastly where the softener would go. If this can help you in any way just put use the dispencers as fits the washing.goodluckKolbrun
2/26/2012 8:05:48 PM • Kenmore HE2... • 333 views • 1 helpful votes
0helpful
1answer

Water won't stop filling the washer

water fill valve is probably stuck open. see if you can find a blockage or just replace it
2/3/2012 3:48:47 PM • Kenmore HE2... • 459 views • 1 helpful votes
0helpful
1answer

No power or lights, locked

This will be a controller failure, It could be caused by many different faults and would require a service person to diagnose onsite.
3/11/2012 12:43:24 AM • Kenmore HE2... • 28 views • 0 helpful votes
Not finding what you are looking for?
Kenmore HE2 Plus 3.6 cu. ft. Super Capacity Front Load Washer Logo

Popular Tags

16 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

vince

Level 3 Expert

1527 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

HE2 Kenmore

  • HE2 Kenmore

Most Popular Question

kenmore front loader washer powers but

  • Washing Machines
Loading...