20 Most Recent Kenmore HE2 Plus 3.6 cu. ft. Super Capacity Front Load Washer - Page 3 Questions & Answers

0helpful
1answer

No power or lights, locked

This will be a controller failure, It could be caused by many different faults and would require a service person to diagnose onsite.
3/11/2012 6:06:13 PM • Kenmore HE2... • Answered on Mar 11, 2012
0helpful
1answer

My kenmore he2 wont dispence the soap in the soap dispencer

Evening to youAllow the washer to start a cycle and have the dispenser drawer ajar and observe through which dispenser the water goes.Does the first stream go through the pre-wash dispencer,secondly notice where the main stream goes and lastly where the softener would go. If this can help you in any way just put use the dispencers as fits the washing.goodluckKolbrun
2/29/2012 5:07:11 PM • Kenmore HE2... • Answered on Feb 29, 2012
0helpful
1answer

Water won't stop filling the washer

water fill valve is probably stuck open. see if you can find a blockage or just replace it
2/4/2012 5:00:16 PM • Kenmore HE2... • Answered on Feb 04, 2012
0helpful
1answer

My Kenmore Elite 796.31523211 won't drain and gives OE error?

Question edited for clarity, add some CAPS and punctuation! It is certainly a drainage issue. Check the connectors on the main board or timer dial. Also check the drain pump actually works. @ronhurley the error code "OE" is a "Drain error " and it is initiated by your washer not having fully drained in 10 minutes. Most common cause is a clogged filter. Jan 17, 2016

meaning of OE code - Kenmore Elite HE3 Washing Machine

.https://www.google.com/search?q=my+kenmore+elite+796+oe+error+code .
1/26/2023 3:37:16 AM • Kenmore Washing... • Answered Yesterday
0helpful
1answer

How to access small hoses & inlet valve diverter attached to top cover & back panel preventing cabinet removal? Kenmore Triple Dispenser Automatic top load washer #11022992103

Try taking off the top. This is held by two spring clips that can be released using a pair of putty knives. Slide the putty knives in from the front of the cabinet on each side so that you push down on the clips. Then you can remove the top. The clips are part 6 on the top and cabinet diagram here: https://www.searspartsdirect.com/model/2y7mjzejlr-000582/kenmore-11022992103-washer-parts . I hope this helps. We had a problem with a similar washer and the only way to access the inlet valves was to remove the top, as above. Cindy Wells
1/21/2023 10:29:43 PM • Kenmore Washing... • Answered on Jan 21, 2023
0helpful
1answer

My kenmore 600 series washer is throwing a LF code. I cleaned the water screens in both outlets. What could be the problem?

Not an expert, but I'd unplug (or reset the breaker) leave it off for a minute and then plug it back in.
1/21/2023 2:09:29 AM • Kenmore Washing... • Answered on Jan 21, 2023
0helpful
1answer

I have a kenmore model 110,5142510, SER C60420403 water does not come out sounds like motor wants to run but it doesn't do anything

It sounds like there may be an issue with the water inlet valve on your Kenmore washing machine. The water inlet valve controls the flow of water into the washing machine and it could be that it is not opening properly, preventing water from entering the machine. Another possible issue is with the water pressure, the water pressure may be too low. It could also be a problem with the lid switch, if the lid switch is not functioning properly, the machine will not start. This switch is located inside the washing machine and is activated by the lid. It is designed to prevent the machine from running if the lid is open. It's also possible that there is a problem with the motor, which is preventing the machine from spinning. It is recommended that you contact a professional to diagnose and repair the problem as these are complex machine and it's better to be handled by a specialist.
1/20/2023 9:59:21 PM • Kenmore Washing... • Answered on Jan 20, 2023
0helpful
1answer

I have an E24 message on my Kenmore dishwasher - model 630.1390

The E24 error code on a Kenmore dishwasher model 630.1390 typically indicates a problem with the drain pump or the drain hose. This can cause the dishwasher to start adding water but then shut off and display the E24 error message. Here are some steps you can try to fix the issue:
  1. Check the drain hose for any clogs or blockages. Make sure the hose is not kinked or bent and that it is properly connected to the garbage disposal or drain.
  2. Inspect the drain pump for any debris or foreign objects. Clean out the pump, if necessary.
  3. Check the air gap on the dishwasher. Make sure it is not clogged or blocked.
  4. Inspect the control board and check for any error messages.
  5. Power off the dishwasher and unplug it for 10 minutes to reset the electronic control board.
  6. Make sure the dishwasher is level and that the legs are adjusted properly.
If the problem persists even after trying these steps, it might be best to contact a professional technician for further diagnosis and repair.
1/20/2023 6:00:31 PM • Kenmore Washing... • Answered on Jan 20, 2023
0helpful
1answer

Repair water leak during fill cycle kenmore top load series 110 washer

here are some ideas..... https://www.repairclinic.com/RepairHelp/How-To-Fix-A-Washing-Machine/45-6-151416-/New/Kenmore-Washer-Leaking-Water-110-92587210
1/16/2023 11:21:30 PM • Kenmore Washing... • Answered on Jan 16, 2023
0helpful
1answer

Where is the the lint filter for the Kenmore HE2

Where is the lint tray on kenmore He 2t washer !
1/13/2023 8:31:27 PM • Kenmore Washing... • Answered on Jan 13, 2023
0helpful
1answer

Kenmore washing machine model 110 22692 100 squeals when it spins and drains . What is making it squeals?

never seen under one before google how to see belts under washer or buy the service manual from maker. moved you out of cars.
1/12/2023 1:01:05 PM • Kenmore Washing... • Answered on Jan 12, 2023
0helpful
1answer

Kenmore stackable washer/drier. Water doesn't drain out.

Kenmore stackable washer dryer doesn't cycle (doesn't advance to water fill or wash, drain, rinse, spin) (not spinning, draining, filling?) After the video, we learned it was the points in the timer. It wasn't the black "electrical plug", being plugged into. Get your serial number and google Kenmore timer and you can order a replacement timer. Even if you still have someone come out, you've still saved a bunch!.......ps....I had a viewer make a good point!; I obviously didn't have any issues, but obviously be careful with electrical panel and any loose wires!
1/10/2023 10:35:53 AM • Kenmore Washing... • Answered on Jan 10, 2023
Not finding what you are looking for?
Kenmore HE2 Plus 3.6 cu. ft. Super Capacity Front Load Washer Logo

Popular Tags

16 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

vince

Level 3 Expert

1522 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

HE2 Kenmore

  • HE2 Kenmore

Most Popular Question

kenmore front loader washer powers but

  • Washing Machines
Loading...