20 Most Recent Electrolux EWFLS70JSS - Front Load Washer with Wave-Touch Controls Fea - Page 6 Questions & Answers

Water does not come into the softener section on the last rinse or the overflow holes are clogged or electric valve for rinse is faulty. My experience is that in over 95% of cases mechanical failure because some residues or deposited calcium carbonate at the water inlet holes (water inlet holes clogged above softener compartment). Practical advice: - If required, pour fabric softener into the compartment marked (the amount used must not exceed the "MAX" mark in the drawer). Otherwise, softener could be takes in washing or prewashing phase what can cause stains on laundry depending on temperature. (Especially in washing phase at 60-90 Celsius) - If you use thick softeners it is recommended to dilute with water. - After washing cycle finish, residues of detergent, softener and water may remain in the dispenser. It is recommended to clean the dispenser regularly to remove any residue. Dado

Dado

Abnormal condition of spin-dry • The safety switch works 3 times continuously. The number window LED display abnormal code: "E3" and begin blinking on and off at the same time and the electric buzzer sounds to indicate a problem. Dado

Abnormal condition of spin-dry • The safety switch works 3 times continuously. The number window LED display abnormal code: "E3" and begin blinking on and off at the same time and the electric buzzer sounds to indicate a problem. Dado

my electrolux EWT606 will not spin. it drains and then just wont go into spin cycle....no error messages it just beeps. can anyone help me please as i have kids with disabilities and NEED to wash!

try resetting the circuit breaker, otherwise.... see this prior answer http://www.fixya.com/support/t13310347-electrolux_oven_edee63as_getting_error

I have the same problem "no power at all" when plug into the power wall inlet. No lamp on, display is blank/no led of 7 segments lit, nothing. The door can be opened and closed normally. Holding Delay and Extra Rinses buttons when power on the electrolux EWF 1074, doesn't help either. The electricity wall plug in is active. What can I do more ?

You're probably right per error code. But most likely if you smell electrical burning, it's you main board issues if you bought pressure switch get the main board as well, part no. 134640610.

If you purchased this washer it should come with 4 shipping bolts on the back. Hopefully you saved it, if not you could probably order one based on your model. Fabricating some could potentially damage internal parts. If you can't find shipping bolts, you could probably buy some screws that would fit in the back with sleeves and washers.

https://www.youtube.com/watch?v=J7vzWGMvfOM https://www.youtube.com/watch?v=72nvG68XtDQ https://www.youtube.com/watch?v=EB-bDYsY4ew

look for manuel https://www.electrolux.fr/support/user-manuals/

https://www.applianceblog.com/mainforums/threads/58174-EIFLW55HIW0-E58-E59-error-codes-no-spin

http://electronicshelponline.blogspot.com/ http://homenol.blogspot.com/ Visit this site to get some details.

http://washererrorcodes.com/electrolux-washer-error-codes Electrolux EWM1100 Service Manual Troubleshooting According To Alarm Codes...

check the top edge of the front panel, sometimes there's two clips, one on the left top and one on the right top of panel. undo the clips and it should come off. Or if there are no clips you might have to just lift up to clear a notched edge. Clips could also be on the bottom, Either way most machines have a second way of holding the panels or tops on. hope this helped. Lynn

first try reversing the hoses to see if that remidies it.

hello... it may help... error descr. cause action reset E43 Power triac on door interlock faulty Door safety interlock faulty; Wiring faulty; Circuit board faulty. Safety drain, door released Selector on "0"