20 Most Recent Tricity Bendix AW1054 Front Load Washer Questions & Answers


Click on your model number (below FIXYA) on this website, type in & search. You will get a shortlist; click on your model, below the page you will get Manual/Guides. Click on the blue, u hv your manual on line. If available that is............

Tricity Bendix... | Answered on Jul 21, 2012


It is possible that the machine does not start off the cycle because there are errors or back feedback from the inputs. For the program to start up the main program controller must initiate the INLET valve to open up and allow water to flow into. If this does not happen then the voltage at the inlet valve must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.In this case the flow being low it can be fault of the inlet valve or the inlet filter.

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

Tricity Bendix... | Answered on Jul 19, 2011


Hello, Welcome to FixYa.

Hopefully the info below will supply you with the assistance to get the door open, but first

**The door typically won't unlock as a result of the unit failing to drain due to a pump or filter obstruction, excessive suds, but the pump failing can cause this as well**


**Unplug the washer from the wall or turn off the breaker before attempting any repairs...safety first**


This is generalized info regarding most front load washers which differ from other models. I believe it will resolve the issue with yours.


Start by following this guide for accessing and cleaning the pump filter...

macmarkus_578.jpg

The next step is as follows,


macmarkus_579.jpg



That should resolve the problem, As I also alluded to before there is a small possibility the pump itself is faulty, but not likely.

Thanks for choosing FixYa and good luck. Let me know if you need further assistance or if any of this is unclear.

Regards,

Macmarkus :)

Tricity Bendix... | Answered on May 10, 2011


Hi,
When my washer did that, I found that the shocks that hold the tub were bad...

Check out this tip I wrote about the noise and vibration that front loadwashers can make..

Washer Problems Washer noise when spinning
heatman101

Tricity Bendix... | Answered on May 04, 2011


That is a contact to ground , either on inlet valve connector or on wiring harness. If it is not that it can be a bad timer board, but that is really unusual in this case.

Tricity Bendix... | Answered on Mar 28, 2011


The circuit boards of these machines are not repaired, they are replaced, so only the engineering diagrams would exist and the factory would have them only.. As far as parts go we have no way to resource parts, we are STRICTLY a technical advice site. We are USA based so Have no way to find where you can buy parts in your home country from California USA.

Tricity Bendix... | Answered on Mar 08, 2011


Hi from retired Englishman in SW France,

If it is carrying out the wash and rinse cycles OK it sounds very much like the belt could be slipping. Belts are not expensive- sorry I do not know how much yours would cost- and are easy to be changed by a competent person:-
REMOVE POWER FROM THE MACHINE AND REMOVE THE BACK.
The motor support bolts should be loosened and the old belt removed. Often putting the new belt on is a bit of a struggle, even with the motor 'loose', because it is new and smaller!
Once on it should be tensioned by pulling the motor against the belt firmly- but not over tight- and the motor support bolts tightened.
ON NO ACCOUNT SHOULD ANY FORM OF LEVERAGE BE USED TO TENSION THE BELT. THAT COULD LEAD TO DAMAGE TO THE BELT, MOTOR AND BEARINGS- EXPENSIVE!
If it turns out to be the motor, it is false economy to just have the brushes changed. Experience of others is that the brushes may only last months unless, that is, the motor is totally refurbished.
Hope this is your problem solved.
Good luck,
John C

Tricity Bendix... | Answered on Feb 19, 2011


Hi,

Please see the article bellow to understand how to replace the door seal.

http://www.ehow.com/how_6639672_replace-washer-front-door-seal.html

You can purchase from ebay or the link bellow:

http://www.amazon.com/Whirlpool-Washing-Machine-Washer-8182119/dp/B002ZNPA7I

Thanks

Tricity Bendix... | Answered on Nov 20, 2010


replace drive belt

Tricity Bendix... | Answered on Oct 21, 2010

Not finding what you are looking for?
Tricity Bendix AW1054 Front Load Washer Logo

40 questions posted

Ask a Question

Usually answered in minutes!

Top Tricity Bendix Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Tricity Bendix Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Tricity Bendix Washing Machines

  • Tricity Bendix Washing Machines

Most Popular Question

bendix aw1054 front loader wont fill as

  • Washing Machines
Loading...