20 Most Recent Zanussi 24 in. ZDT6041 Built-in Dishwasher - Page 4 Questions & Answers


Could be anything!
If you suspect that there is a fault then it will be displayed by blinking LED "END OF CYCLE". As the display of failure in hexadecimal code it can flash up to max. 15 times than short pause and after that repeat fault code. You must to count the number of times the LED "END OF CYCLE" flash up.

Example from user manual: Anti-flood device is activated.
- continuous flashing of the indicator light of the running programme
- 3 intermittent audible signals
- 3 flashes of the END OF CYCLE indicator light
(which means "i30" fault code, the cycle is interrupted and the
drain pump switches on).
Possible causes:
Water leakage from the tub - sump and various connections
(pump, upper spray arm duct etc.); floating sensor blocked
mechanically; microswitch faulty; fill solenoid blocked
mechanically; circuit board faulty (solenoid triac short-circuited);
wiring faulty.
26226179-aipk5px1bmfkdpsmrgevaqwn-3-1.jpg Could be also:
To cancel a washing programme in progress:
- Open the dishwasher's door.
- Press the programme selection/cancel button for about 3 seconds,
until the indicator light of the running programme turns off and the
END OF CYCLE indicator light flashes, indicating that the running
programme has been cancelled and that the machine has
returned to setting mode. It is now possible to select another
washing programme. If a new washing programme will be
selected, check that there is detergent in the detergent dispenser.

NOTE: only during the drying phase, if the dishwasher's door will be opened and remains open for more then 30 seconds, the running programme will be automatically cancelled and the machine will return to setting mode. This will happen, always only during the drying phase, also when the machine is switched off by pressing the
On/Off button and remains switched off for more then 30 seconds.

Dado

Zanussi... | Answered on Sep 22, 2016


First you need to remedy failure or any leakage than reset appliance.
Under Reset I mean to delete all alarm stored in memory.

1. Turn off the dishwasher.
2. Press and hold S1 while switching on the dishwasher. Keep
holding the Program button until:
- LED L1 blinks, L2 and L3 is on
- Release S1
3. When L1 is blinking, L2 and L3 is on, press the S1 before L2 and
L3 is turned off.
- LED L2 is blinking, L1 and L3 is turned on.
4. Wait till L1 and L3 is turned off, then press S1
- All used LEDs flash 5 seconds on 1 second off repeatedly.
- If buzzer is equipped, it beeps for 5 seconds
- The alarms saved in the memory are erased
5. Switch off the appliance.

26259192-aipk5px1bmfkdpsmrgevaqwn-3-1.jpg Dado

Zanussi... | Answered on Sep 22, 2016


26269906-aipk5px1bmfkdpsmrgevaqwn-3-0.jpg "3 in 1" function
This appliance is equipped with the "3 in 1" function, that
allows the use of the "3 in 1" combi detergent tablets.
This function can be selected with all washing programmes.
With the selection of this function the inflow of rinse aid and
salt from each respective supply container is automatically
deactivated and also the indicator lights for salt and rinse aid
are deactivated.
Select the "3 in 1" function before the set of a washing
programme.
Once this option is selected (indicator light illuminated) it will
remain active also for the following washing programmes.
With the use of the "3 in 1" function, the cycle durations may
change. In this case, in the digital display, the indication of the
running time of the programme is automatically updated.
NOTE: Once the programme is running, the "3 in 1" function
can NO longer be changed. If you want to exclude the "3 in 1"
function you have to cancel the programme setting (see
chapter "Starting a washing programme" - "Cancel a washing
programme in progress") and then deactivate the "3 in 1"
function.
In this case you have to set a washing programme (and
options) again.

Activation/deactivation of the "3 in 1" function
(The dishwasher must be switched off)

1. Press the On/Off button. The On/Off indicator light
illuminates (setting mode).If a programme button indicator light is on, this means that a washing programme is set. The programme must be cancelled: press simultaneously function buttons 2 and 3
for about 2 seconds. All the indicator lights will turn off (except for the On/Off indicator light and eventually salt and rinse aid indicator lights) indicating that the set programme has been cancelled and the machine is now in setting mode.

2. Press simultaneously function buttons 2 and 3, until the
indicator lights of function buttons 1, 2, 3 and 4 start
flashing.

3. Press function button 4, the indicator lights of function
buttons 1, 2 and 3 turn off while the indicator light of function
button 4 goes on flashing.

4. Press function button 4 again, the "3 in 1" indicator light
illuminates, indicating that the "3 in 1" function is active.
To deactivate the function press function button 4 again, the
indicator light turns off.

5. To memorise the operation, switch off the dishwasher by
pressing the On/Off button or wait about 60 seconds after
which the dishwasher will automatically return to setting
mode.

Dado

Zanussi... | Answered on Sep 22, 2016


i40 Alarm Code - family : Analogue pressure sensor problem.


26055530-1ker2qxuzgbar1gk4s3oqzxl-1-0.jpg Dado

Zanussi... | Answered on Feb 08, 2016


If you have a Zanussi clothes dryer, I can only give you generic information.
Here goes.
In the US, clothes dryers will not heat for 3 reasons, normally:
1) The heating element has failed, usually the heating coil has burned in two.
It will need replacement.
2) One of the thermostats or the fuse has failed, and must be replaced.
The fuse and the thermostats ( there are up to about 5 on newer machines) are there to prevent the machine catching fire should it overheat.
3) One of the wires inside the machine has burned in two, or has broken inside the machine.
God bless your efforts.

Zanussi... | Answered on Jan 19, 2016


Most often when refilling the water supply system with water and bring it trash that usually clogged grid in the water supply and the appliance does not get water or it slowly filled appliance (time out water intake). I would in your place disconnected inlet hose and clean the grid located at the entrance of water (inlet valve) in the appliance and sometimes between the pipe and the inlet hose.



Dado

Zanussi... | Answered on Dec 13, 2015

Not finding what you are looking for?
Zanussi 24 in. ZDT6041 Built-in Dishwasher Logo

8 questions posted

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

Paul Carew

Level 3 Expert

3489 Answers

Renee Knafel-Bullock
Renee Knafel-Bullock

Level 2 Expert

353 Answers

ray gallant

Level 3 Expert

66490 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Zanussi Dishwashers

  • Zanussi Dishwashers

Most Popular Question

dishwasher hose 2 splits in need know

  • Dishwashers
Loading...