Top 20
Zanussi ZWD1470W Front Load Washer / Dryer Questions & Answers
E34 error zanussi washer
Incongruence between level of electronic
pressure switch and level of anti-boiling
pressure switch 2 (duration of fault at least 60
seconds).
Cycle is blocked with door closed.
Could be: Hydraulic circuit of pressure switches; electronic
pressure switch; pressure switch; wiring between main PCB and electronic pressure switch; wiring between main PCB and safety pressure switch; and finally main PCB.
Dado
Err message whatever I press!
Try unplugging the washer, wait about 10 minutes and plug it back in. Maybe this will reboot your washer. Since most new washers are digital and maybe this will help. Good luck
Machine had been giving E20 error code - filter
E20 is an error code for drainage failure. Check where the appliance drain hose connects to the house drains for a blockage.If it's onto a spigot under the sink, take them off and check both for a blockage.If these are ok then it's likely to be a blockage in the pump. You'll need to drain the water out manually.Put a shallow dish below the filter and slacken the filter.Tighten it to stop the flow of water while you empty the dish.Once empty, take the filter out, clean out the debris and ensure nothing is left jamming the pump.Before refitting the filter, put the machine on drain or spin and listen at the filter housing to see if you can hear the pump running.If you do, fit the filter and try the machine again.Thanks for using FixYa
Fabric conditioner stays in the tray?
Hi from retired Englishman in SW France,
I suspect that the conditioner/softener tray needs a thorough clean, paying particular attention to the sentences in
BOLD ;-0)
-------------------------------------
Remove the complete drawer. To do this you will have to do one of the following-
- Top catch-
push down the lip/catch at the middle rear and pull the drawer out (that's how our Bosch one is removed)
- release the catches underneath (our daughter's Indesit) or
- lift upwards on the tray as it is coming out to clear the lip underneath.
One of these should enable you remove it
(I am having to guess some of the following!)
Once out identify which tray is for the conditioner- the others are simply 'chutes' and open-ended.
It will normally have some sort of cover over it which you must remove to expose the little stuck up pipe/tube. On some models there is just a small individual cap over the tube. The tube is down which the conditioner and water should siphon. It is likely to be blocked by 'gunge'- a mix of powder and conditioner. The whole of the tray, particularly this pipe and the bit which fits over it, must be completely clean and clear for it to operate correctly. It is worthwhile checking fairly regularly.
If this does not work, pull out the dispenser drawer far enough to be able to just see the softener tray, select the (final?) rinse and check that water is entering the tray. If it isn't there is a fault with the water distribution and an engineer call is required ;-0(
Good luck,
John C
Dryer working fine but no heat coming through,
Hi,
If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.
if you dryer is gas check out this gas no heat tip....
If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.
check out this electric no heat tip...
heatman101
][\[]\\][
MACHINE NOT SPINNING everything else is fine.
It could be either the bearings have collapsed and seized or that an object such as a sock,stone,screw or the like has got down into the drum and jammed it solid.one way to see if it is a small object like a stone or screw which may work is to undo the screw on the pulley,this is normally a torx screw,you will have to undo in an anti-clockwise direction,then gently prise off the pulley but be careful its soft alloy and could break,once off try jiggling the drum it has some end play and this may be enough to release the jammed article.If this does not do it then the drum will have to come apart if it is a split type drum unit.Also try looking around the front by the door seal sometimes if a sock gets stuck it can get jammed around this point and you may see it.
My zanussi washer dryer has some problem When i
check the drain filter is not blocked if it does not empty all the water it saves time on the next fill. also the spin will not happen if it has not emptied completley. a faulty pump would give the same effect.
My drum on my ZWD14270W
Hello,
It could be either the bearings have collapsed and seized or that an object such as a sock,stone,screw or the like has got down into the drum and jammed it solid.one way to see if it is a small object like a stone or screw which may work is to undo the screw on the pulley,this is normally a torx screw,you will have to undo in an anti-clockwise direction,then gently prise off the pulley but be careful its soft alloy and could break,once off try jiggling the drum it has some end play and this may be enough to release the jammed article.If this does not do it then the drum will have to come apart if it is a split type drum unit.Also try looking around the front by the door seal sometimes if a sock gets stuck it can get jammed around this point and you may see a piece if so then try pulling out with a vice grips,normally takes a hell of a lot of sheer force to pull it out.
Hope this helps.
My Zanussi ZWD 1470W won't fill up with water. I
Story could be lengthly so in brief, check to see if drain pump is not blocked and if door latch is functioning correctly.(use a multimeter if you can). If it all measures out as good, then your control is faulty. Does the water fill up to the correct level when you start the cycle? Does the motor hum when trying to run. If so check the capacitor.
Error e40 come up on my washing machine zwd 1472 s
Hello,
E40 normally points to a fault at the door switch,sometimes when the door switch fault occurs it can also cause damage to the main P.C.B.(Programmer).As this machine is still in the major parts warranty it would be advisable to get in touch with Electrolux.
ZWD1471 S E90 ERROR MESSAGE WHAT DOSE IT MEAN ?
E90 means Communication error between user interface and main board. Verify the connector between the main board and user interface board by plugging and unplugging the connector few times on both sides... if still the same fault then main pcb board is replaced 1st tried then the user control pcb is still the same...
Not finding what you are looking for?