20 Most Recent Zanussi ZWD1470W Front Load Washer / Dryer Questions & Answers


That means a sevies tech has got to come out an unlock
it the main board is bad these front loaders
are bad about this they will lock up all your
cloths

Zanussi ZWD1470W... | Answered on Jun 13, 2014


Try unplugging the washer, wait about 10 minutes and plug it back in. Maybe this will reboot your washer. Since most new washers are digital and maybe this will help. Good luck

Zanussi ZWD1470W... | Answered on May 13, 2014


Make sure that you have screwed the filter back in tight, and also check that there is no dirt or anything else round the filter seal to stop it sealing proerply.

Zanussi ZWD1470W... | Answered on Sep 08, 2013


fabric conditioner is dispensed during rinse cycle, if it does not work then either, try pouring hot water into dispenser, as conditioner tends to get goopie when dry, thus may have clogged up

Zanussi ZWD1470W... | Answered on Jul 30, 2013


hi there e40 fault is a problem with your door interlock. get it replaced and all will be fine..

Zanussi ZWD1470W... | Answered on Mar 25, 2013


see the video and fix it. God bless you

Zanussi ZWD1470W... | Answered on Sep 28, 2012


Hello ALARM CODES Alarm code Description of fault User code Effect E11 Problems with water fill in wash phase E10 Cycle PAUSED 8.2 E12 Problems with water fill in drying E10 Cycle PAUSED 8.3 E21 Problems with water drain in wash phase E20 Cycle PAUSED 8.4 E22 Problems with water drain during drying or drying condenser blocked E20 Heating phase skipped 8.5 E31 Analogic (electronic) pressure switch circuit faulty --- Cycle blocked with door closed 8.6 E32 Incorrect calibration of analogic (electronic) pressure switch --- Cycle PAUSED 8.7 E33 Incongruency between level of analogic (electronic) pressure switch and level of anti-boiling pressure switch 1 --- Cycle blocked with door closed 8.8 E34 Incongruency between level of electronic pressure switch and level of anti-boiling pressure switch 2 --- Cycle blocked with door closed 8.9 E35 Water level too high --- Cycle blocked with door closed and water drain 8.10 E36 "Sensing" circuit of anti-boiling pressure switch 1 faulty --- Cycle blocked with door closed 8.11 E37 "Sensing" circuit of anti-boiling pressure switch 2 faulty --- Cycle blocked with door closed 8.11 E38 Pressure chamber blocked --- Heating phase skipped 8.12 E41 Door open E40 Cycle PAUSED 8.13-14 E42 Problems with door closure E40 Cycle PAUSED 8.15-16 E43 TRIAC which powers the door interlock faulty E40 Cycle PAUSED 8.17-18 E44 "Sensing" circuit of door delay interlock faulty --- Cycle blocked 8.19 E45 "Sensing" circuit of door delay interlock triac faulty --- Cycle blocked with door closed 8.19 E51 TRIAC which powers the motor short-circuited --- Cycle blocked with door closed (after 5 attempts) 8.20 E52 No signal from tachometric generator --- Cycle blocked with door closed (after 5 attempts) 8.21-22 E53 "Sensing" circuit of motor TRIAC faulty --- Cycle blocked with door closed 8.23 E54 Relays (motor) contacts faulty --- Cycle blocked with door closed (after 5 attempts) 8.23 E61 Insufficient heating during washing --- Heating phase skipped 8.24 E62 Overheating during washing --- Drain, end of cycle 8.25 E63 Insufficient heating during drying Heating phase skipped 8.26 E64 Overheating during drying --- Heating phase skipped 8.27 E66 Power relay to heating element faulty --- Drain, end of cycle 8.28 E71 NTC wash sensor faulty --- Heating phase skipped 8.29 E72 NTC sensor on drying condenser faulty --- Heating phase skipped 8.30 E73 NTC sensor on drying duct faulty --- Heating phase skipped 8.31 E84 "Sensing" circuit on circulation pump triac faulty --- Drain, end of cycle (door open) 8.32 E85 Circulation pump faulty --- Drain, end of cycle (door open) 8.33 E91 Communications error between main PCB and user interface --- --- 8.34 E93 Configuration error E90 Cycle blocked 8.34 E94 Incorrect configuration of washing cycle E90 Cycle blocked 8.34 EF1 Drain filter blocked LED-EF0 --- 8.35 EF2 Excessive detergent LED-EF0 --- 8.35 Regards David Marsh

Zanussi ZWD1470W... | Answered on Aug 16, 2012


E20 is an error code for drainage failure.



Check where the appliance drain hose connects to the house drains for a blockage.

If it's onto a spigot under the sink, take them off and check both for a blockage.

If these are ok then it's likely to be a blockage in the pump.



You'll need to drain the water out manually.

Put a shallow dish below the filter and slacken the filter.

Tighten it to stop the flow of water while you empty the dish.

Once empty, take the filter out, clean out the debris and ensure nothing is left jamming the pump.

Before refitting the filter, put the machine on drain or spin and listen at the filter housing to see if you can hear the pump running.

If you do, fit the filter and try the machine again.


Thanks for using FixYa

Zanussi ZWD1470W... | Answered on Oct 11, 2011


E20 is a general error code to get to the real problem try this.. Reading ErrorCodes 1. Wake the washer by pressing any button. 2. Wait 5 seconds. 3. Press and hold

Zanussi ZWD1470W... | Answered on Oct 11, 2011

Not finding what you are looking for?
Zanussi ZWD1470W Front Load Washer / Dryer Logo

96 questions posted

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

peter gittos
peter gittos

Level 2 Expert

247 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Zanussi Washing Machines

  • Zanussi Washing Machines

Most Popular Question

zanussi zwd1470w fabric conditioner

  • Washing Machines
Loading...