Top 20 AOpen (DUW1608/ARR) (914ID37202) Burner Questions & Answers


make sure that the dvd burner is getting enough power test all leads that are attached to the dvd burner including electical extensions and make sure they have a secure connection or just replace them there might be bad/faulty or your drivers may have been corrupted or you might have a virus run your antivrus program you might have to physically unplug the leads for this cd/dvd burner then plug them back in or you might have to uninstall then reinstall your DVD/CD or uninstall the driver then reinstall for this device control panel admistrive tools,computer management,device manager scroll down cd dvd rom drives right click you can you can update driver,roll back driver,or select properties general troubleshoot, select driver click to reinstall drivers click update driver or uninstall then reinstall hope this helps if this does not fix the problem it might be a registry problem Close all open programs

Click on Start, Run, and type regedit and press Enter Click on the plus signs (+) next to the following folders

HKEY_LOCAL_MACHINE

SYSTEM

CurrentControlSet

Control

Class

{4D36E965-E325-11CE-BFC1-08002BE10318}

This folder is the DVD/CD-ROM Drive Class Description in the registry. Look for any of the following names in the right hand column.

Upper Filters

Lower Filters

Upper Filters.bak

Lower Filters.bak

If any of the above keys shown in step 4 are listed, right-click on them and choose DeleteAfter deleting the keys, close the registry editorReboot your computerOpen My Computer and check to see if your CD or DVD drives have returned. You may also want to open Device Manager and verify that the yellow exclamation and error code on the CD or DVD drive is gone. hope this helps

AOpen... • 159 views • 0 helpful votes


Is there a floppy disk in the A: drive? That "port" is usually reserved for a floppy disk, either 3.5 or 5.25in. You probably need to disable the floppy drive in the BIOS.

AOpen Computers... • 34 views • 0 helpful votes


You can go to the link below and enter the board name is a MX4GER and that will give you your manuals Download Center

AOpen Computers... • 359 views • 0 helpful votes


I am assuming that you are replacing or installing a new mobo. You need to read the manual to see if it has an option for speakers, most do. You need to look the details for the "front panel" where you connect wires for power, hard disk lights etc.

AOpen Computers... • 88 views • 0 helpful votes


if you are directly connected to the router via ethernet go through the ip gateway, open up a web browser usually d-links ip gateway are 192.168.1.1, you might have to look up you model. Also note you may have a default login and password, such as admin for password and admin for user. note you can also reset the password on the router by holding the reset button for 10 seconds. More questions heres a refrence guide http://www.dlink.com/-/media/Consumer_Products/DSL/DSL%202750B/Manual/DSL_2750B_B1_Manual_v1_00_EN.pdf

AOpen Computers... • 69 views • 0 helpful votes


http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=23&PFid=23&Level=4&Conn=3&DownTypeID=3&GetDown=false#1

AOpen Computers... • 57 views • 0 helpful votes


number?

AOpen Computers... • 150 views • 0 helpful votes


If you open your motherboard, then you can see a lot of input and output ports behind the motherboard, where you connect VGA, mouse, keyboard etc wires at that place there is a 3.5mm jack which may be green in color, you can connect specker wire there A red mark is shownf0e57a9b-b042-492e-a159-ddede3ddc5aa.jpg

AOpen Computers... • 72 views • 0 helpful votes


CHECK THE ELECTRICS IS PSU WORKING ?

AOpen Computers... • 113 views • 0 helpful votes


go to aopen download support web site download them from them there

AOpen Computers... • 451 views • 0 helpful votes


You can find the documentation on this webpage (downloadable pdfs) http://www.asrock.com/mb/overview.asp?cat=Manual&Model=A55M-HVS This for the motherboard ASRock A55-HVS which supports socket FM1. Up at the top left of this webpage are links to other information about this m/b - eg overview, CPU support list, specs, downloads, etc 13.April.2014

AOpen Computers... • 98 views • 0 helpful votes


There will be a screw or two on the side of your case. Follow these simple steps. Shut down computer. Disconnect all wires from tower and move it to a place, such as a table. where you can do the work. Using a phillips head screwdriver remove the screw(s) holding the case together on the side that is removable (usually the left side) Look inside the case, you will see a slot that matches your graphics card. It is called a PCI-E slot, look it up if you are unsure of what one looks like. Remove the metal tab that is blocking the hole in front of the slot, and slightly to the side. It will either pull out or be held in by a small screw (save the screw if it is there). Gently, but firmly, line up the graphics card's pci-e connector with the slot in the motherboard. It will require a firm, but gentle nudge to snap into place. Don't force it and make sure you are lined up. If it's seated correctly the metal slot on the front will line up with the metal tab you just removed. If you have a graphics card installed already, remove it. Reinstall the side of the case. Connect all wires, but this time connect your monitor's connection (either DVI (white), VGA(blue) or HDMI (black and gold) to the graphic's cards video port. Power on the computer. Here the steps can vary. If you didn't remove a graphics card earlier you need to disable the onboard graphics. I would need to know the manufacturer of your motherboard to give instructions on how to do it. Insert the disk that came with your graphics card and install the software included with it. Play games.

AOpen Computers... • 58 views • 1 helpful votes


Hi, Do nothing with the hard disk. Remove it and mount it on another working machine. Use the second machine to run recuva.

AOpen Computers... • 49 views • 0 helpful votes


check out drive

AOpen Computers... • 31 views • 0 helpful votes


check memory, it is a system timer failure (if the beeps are short), usually its because of bad ram, but if u took it apart could be you just need to check how you inserted the RAM.

AOpen Computers... • 53 views • 0 helpful votes


Hi,1> Click Start and then Control Panel2> In Control Panel, if you are in Category View, click on Switch to Classic View3> Open Regional and Language Options in Control Panel.4> Click on the Languages tab.5> Under Supplemental language support, select the check box beside the applicable language collection6> Click OK or Apply. You will prompted to insert the Windows CD-ROM or point to a network location where the files are located. After the files are installed, you must restart your computer.Thanks..

AOpen Computers... • 42 views • 0 helpful votes


What relay are you talking about? The only computer I know of that may have a relay in it is from the 1940s. Aopen didn't exist then.

AOpen Computers... • 25 views • 0 helpful votes

Not finding what you are looking for?
Computers & Internet Logo

Popular Tags

1 questions posted

Ask a Question

Usually answered in minutes!

Top AOpen Computers & Internet Experts

Cindy Wells

Level 3 Expert

6259 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Joe Goldman
Joe Goldman

Level 2 Expert

337 Answers

Are you an AOpen Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

AOpen Computers & Internet

  • AOpen Computers & Internet

Most Popular Question

dvd drive starts stops light

  • Computers & Internet
Loading...