Pride Jazzy 600 JAZZY 600 - Answered Questions & Fixed issues

Hi ring this number they might b able to help with youre problem ,,1-800-800-8586.... Cheers

You don't you, replace joystick. However, should you take the joystick apart you may have many hours of intense frustration awaiting you. I’m happy to assist further over the phone at https://www.6ya.com/expert/bill_bcbb89783b08c489

You would need to remove both covers top and bottom of the console holding the throttle pot. Typically, there are 4 or six screws holding the covers. The throttle pot is attached with 2 screws and has 1 electrical plug. The throttle lever on the end of the throttle pot shaft usually is held on with 2 Allen wrench set screws.
Before replacing the part it can be tested using a digital voltmeter.(procedure is described elsewhere).
Obtain the correct replacement part by searching by Model and serial number and part description. The manufacturer website is a good starting point for parts

PDF]INFINFB2043_Jazzy_600-600XL_Troubleshooting_Rev B ...

www.pridemobility.com/download.php?...Jazzy_600-600...

Pride MobilityWhat if the systems on my Jazzy 600/Jazzy 600XL seem to be "dead" (controller does not ... Each controller will flash a code via the battery ... 7. Joystick error. Contact your authorized Pride Provider. Four yellow LEDs ... This is indicated by the VR2/VSI speed ... flash in a numbered sequence followed by a 2-second pause

hi, Joystick code 8 == Controller error Three red LEDs Four yellow LEDs One green LED. Please confirm this, if you're UK based , i can repair these units... regards Rob www.gewizrepairs.co.uk

It may be something as simple that you have picked up a twig or a piece of litter. Lie on the floor and look underneath with a flashlight or get a young person to do it..

Time for new batteries from your description.

Question edited for clarity and toss in a load of CAPS. It is not published. You could ask them, or if you go to an auto paints supplier, they scan the paint on it, mix the paint and put into a spray can for you. https://www.google.com/search?q=Viper+blue+color+code+for+pride+victory+10+scooter ..

the fuse box location may vary depending on the model of the scooter. However, it is usually located under the seat of the Jazzy scooter. You can access it by unscrewing the two bolts that hold the seat in place. Once you remove the seat, you should see a black box with a white label that says "FUSE". The fuse is located inside this box.

Check out the videos on deactivating it. https://www.google.com/search?q=Pride+Celebrity+X+reverse+beeper+location ...

If the latch on your Pride Jet 3 Ultra power wheelchair won't stay latched, there are a few potential causes and solutions you can try:

1. Check for obstructions: Inspect the latch mechanism and the surrounding area for any obstructions or debris that may be preventing it from latching properly. Remove any obstacles and ensure that the latch can move freely.
2. Adjust the latch position: Sometimes, the latch may need to be adjusted to ensure a proper fit. Check if there are any adjustable components on the latch mechanism and try repositioning them to achieve a secure latch.
3. Tighten or replace the latch: If the latch is loose or worn out, it may not hold securely. Check if there are any screws or fasteners that can be tightened to secure the latch. If tightening doesn't solve the issue, you may need to replace the latch with a new one.
4. Seek professional assistance: If the latch continues to have issues or you are unsure about making adjustments or replacements yourself, it's best to contact Pride Mobility or a certified technician for further assistance. They will have the expertise to diagnose the problem and provide the appropriate solution.

Axels do not need greasing. Check the clutch releases properly.

Question edited for clarity, add maker and fix typos. Question moved from Cars and Trucks to Pride Mobility. Please don't type in all CAPS, it is considered SHOUTING and is harder to read. There is no service Manual and no wiring schematic. The manuals only show battery wiring. This is for the Shoprider and it may be close enough https://www.shoprider.co.nz/pdf/troubleshooting.pdf https://www.google.com/search?q=pathrider+140xl+service+manual https://www.google.com/search?q=pathrider+140xl+wiring+diagram ..

Are you refering to the go go ?

This is your manual. It looks like you can't. https://manualzz.com/doc/6792289/power-chair-owner-s-manual ..

Get a can of Electrical Contact Cleaner spray and separate any electrical connectors that you can see, and re-make the connection. You have a bad connection somewhere that is losing contact with a bump. The most likely places are any from the battery, or any to the controller. Make sure the two connector halves are fully locked in place. Some have fuses, some have breakers, check the connections there as well. You say it has only done 8 miles. If you bought it new, it is under dealer and maker warranty. I was hoping to find you a manual, but 'GoGo' is a range of models. https://www.google.com/search?q=Pride+GoGo+manual Shutting off on bumps is a known issue caused by the battery box bumping. https://www.google.com/search?q=Pride+GoGo+shuts+off+on+a+bump ..

Question edited for a lot more clarity. Presumably English is not your first language. Duplicate post with worse English deleted. Refresh page to see your question published. We are FIXYA dot com. We don't sell anything, we only supply FREE information. The best place to buy spare parts is from 'Monster Scooter Parts' in this link. Be aware that Pride Go Go is a range of scooters in 3 wheel, 4 wheel, XL, Traveler, Elite, Ultra and Sport, so make sure you state the correct model. https://www.google.com/search?q=Pride+Mobility+Go+Go+Scooter+parts ..

google go go pride 3 wheel parts