20 Most Recent Stihl Chainsaw Brake Band Strap 038, Ms 380, Ms 381 Questions & Answers

I don't have a copy but try to check with Stihl's website .

Stihl Chainsaw... | Answered on Oct 07, 2013

0 Answers

Hi I was wondering if anyone could tell me where the fuel lines go on a stihl ts420 Concrete saw

Stihl Saws | Posted on Apr 13, 2020 | Be the first to answer

1 Answer

How to remove a carburator from a ts350 stihl concrete saw

handles have to be removed first

Stihl Saws | Answered on Nov 20, 2019

1 Answer

How do I take off choke slide to remove top cover on a stihl ts 350 ?

Hi Harold-

Here is a youtube video STIHL TS 350 Super Cut Off Saw (Pulling The Engine Apart) https://www.youtube.com/watch?v=DIlfGvFvIb4

Hope this helps.

Stihl Saws | Answered on Oct 27, 2019

3 Answers

I have a 420 stihl saw I installed a new carburetor new gas lines won’t start if I pour gas in cyclinder runs for a minute then cuts off need help figuring this one

obviously it's not getting gas. remove the carb and recheck it. some have a plastic piece over the intake and output to keep the interior clean during transit. Forgetting to remove it will cause it not to get gas. Either that or the float is stuck closed, something like that. If the carb is new out of the box, they sometimes have a piece of plastic or something inside the float bowl to keep the float from banging around during shipping ect. Check that too.

Stihl Saws | Answered on Oct 09, 2019

1 Answer

Rebuilt a stihl ts400 new rings,bearings carb electronic module,plug . When I try to start almost pull my hand off. Pulls ok with plug out and still wont pull with plug in and the muffler off

Sounds like you need to check the valve & ignition timing .

Stihl Saws | Answered on Jul 11, 2019

1 Answer

My TS 420 will not prime. I installed a new primer bulb and still no gas. Any ideas? Thanks.

Check the fuel line in the tank to see if it's plugged. Also there could be crack or air leak in the full line not allowing gas to get sucked in. Just some thoughts if you haven't looked at this yet.

Stihl Saws | Answered on Jun 26, 2019

2 Answers

Stihl concrete saw engine broke flywheel side? Why

wear and tear or improper usage

Stihl Saws | Answered on Jun 03, 2019

1 Answer

I need fuel line routing for stihl ts 420 chop saw

Primer bulb to in tank filter - return line from carb to top of fuel tank.

Stihl Saws | Answered on May 19, 2019

0 Answers

How do i take flywheel off stihl ts420 concrete saw

Stihl Saws | Posted on May 11, 2019 | Be the first to answer

1 Answer

I am working on a stihl ts 420 cut off saw with no spark.

Check shutoff switch, wires for grounding, magnet strength on flywheel. If OK replace ignition module .

Stihl Saws | Answered on May 08, 2019

2 Answers

Idle speed screw reset on a stihl br 350

Turn the screw gently clockwise until it won't go in any more. Then turn it anti (counter) clockwise 1 complete turn. That should enable it to start but you will probably need to adjust it when the engine is warm. Failure to start can be because of a range of causes so I suggest you check the basics first like ensuring the fuel is fresh, that there is spark at the plug and that the choke is turned on if the engine is cold.

Stihl Saws | Answered on Apr 06, 2019

1 Answer

My Stihl ts 410 stone cutter wont start i have.spark and fuel at plug. machine is about 2yrs old have you any ideas please

All good answers here. If you have spark and it just quit running sounds more like water in system. The carb cleaners should help but you may need to run quite a bit through it. Remember to use care adding gasoline to avoid getting water into the tank. Also keep your tank full in storage to avoid condensation. In storing tong term add some sea foam and dump it out when you restart. Old gas turns yellow.

Stihl Saws | Answered on Apr 04, 2019

1 Answer

What set spark plug at Ts400 stihl concrete saw

Most Stihl machines use 0.5mm spark gap

Stihl Saws | Answered on Mar 13, 2019

1 Answer

So I've got a stihl ms290 chainsaw that the spark.plug threads are stripped n I saw on this site 2buy a 14mm heli coil kit but there are 3dif types in 14mm size. There's 14mm×2.0, 14mm×1.5, and 14mm ×1.25. Which is proper kit for my stihl ms290 chainsaw

According to Machinery's Handbook (24th ed pg 1650), there are four standard SAE spark plug threads, all metric: M18 x 1.5; M14 x 1.25; M12 x 1.25; and M10 x 1.0

Stihl OEM plug
NGK BPMR7A
Threaddiameter: 14mm
Threadreach: 9.5mm

Stihl Saws | Answered on Feb 14, 2019

1 Answer