Dewalt DCF885C2 20-Volt MAX Lithium Ion 1/4-Inch 1.5 Ah Impact Driver Kit - Answered Questions & Fixed issues

Tap the end of the bit a couple of times with a light hammer. This will often shift it.

Did the light on the charger indicate that it was charging? (Most also have a "replace battery" or similar light.) If so, and the drill keeps beeping...since it's new don't bother monkeying with it. Just take it back to the store and have them replace it. Dealing with a warranty repair will leave you without a tool for some length of time.

There is a small spring at the back of the sleve which snaps. Try replacing it. it is only cheap.

Unfortunately Dewalt switches are solid state, meaning there is little to nothing you can do to fix them when they don't work. Occasionally spraying them with electronics cleaner and blowing them out with clean, dry air will make them work a little longer but more often than not you simply have to replace the switch. The part number for your driver is N084669. They cost between $65 and $75 so shop around or check with a local repair center.

here is a link copy and paste https://sawmillcreek.org/showthread.php?111567-DeWalt-733-Rollers-stopped-moving ..

It needs new blades - likely has a chip in one. See link for replacement tutorial

Red is pos and black is neg.

https://www.weeklytools.com/dewalt-angle-grinder-buying-guide/ When it comes to Angle Grinder, the name of the Dewalt tools maker comes first. We will look at the basic parts and functions of a grinder before purchasing a machine. Then let's see the details without delay.

https://www.weeklytools.com/different-uses-for-an-angle-grinder/ An angle grinder is a multifaced handheld power tools that was invented by a German company. We may don't know a lot about this tool because it is an unrecognized instrument like some other tools. Now we will discuss different Uses for angle grinder. An angle grinder is also known as a side grinder or disc grinder. It is a machine with a rotating abrasive cutting disc. Angle grinders can be powered by an electric motor, petrol engine, or compressed air. It comes in a wide variety of different sizes and powerful motor, each with the other purpose. Once anyone knows about these, he can easily find out the best angle grinder for his needs. Angle grinders are quality fulled equipment for any metal fabrication shop, and those are typically used in auto repair, workshops, and construction sites.

https://www.weeklytools.com/how-to-use-a-nail-gun-with-an-air-compressor/ We may not need a drill machine almost the whole time. But there is a demand for a pilot hole during the home finishing process. This post is not for you if you are a professional. However, in most of the cases, we observe the necessity for a pilot hole. From wooden doors and windows ...

I’m not trying to be a wise guy but the regulator has an adjustment on the bottom

The nailer must be firmly pressed against the surface you are planning to nail. This will arm the nailer in preparation for firing the nail.

Try this link: https://www.ereplacementparts.com/dewalt-dw423-type-inch-evs-random-orbit-sander-parts-c-1009_2742_2758.html

https://www.2helpu.com/PDMSDocuments/EU/Docs/Service%20Dossier/DW733-D.PDF

O rings

Either the blades are incorrectly installed causing the head to jam or the safety cover is not installed properly - there is a safety mechanism that locks the cutter head when the cover is removed.

Typical cause is low voltage - but can also be a bent driver or something jammed in the nail track. Is this a finish nailer or framing nailer?

That symptom usually indicates a low voltage issue - not sure how the adapter may affect this, I've never run them with a 20v battery. Try it with a standard 18v and see if you have the same issue - please comment back with the results, I'm curious.

copy and paste in search engine. took about 5 seconds to find answer. Dewalt Air Compressor D55146 Belt Replacement

Without inspecting tool, it would be hard to definitely tell what part, I would call Dewalt, they will be glad to help you. You do not want to throw parts at it. 1-800-433-9258