20 Most Recent Carrier 42QG24-C / 38QG24-C 24000 BTU SPLIT AIR CONDITIONER FOR 220 VOLTS ONLY - Page 7 Questions & Answers

I would like a manual for this booth

1.Clear Jams. ... 2.Inspect Your Air Supply. ... Reload the Magazine. ... 4.Clean the Instrument. ... 5.Replace Seals and O-Rings. ... 6.Inspect for Harm. ... 7.Take It to the Help Place. Consider https://lumbuy.com/ for buying best quality Nail Gun Machine.

This looks like it is the same... https://manualzz.com/doc/22894271/parts-manual-model-no.-919.1-5281-0

Question edited for clarity. Replace the Start Capacitor. Some have a combined Dual Start/Run capacitor. The capacitor gives it a jolt to get it moving which you are doing by hand. https://www.google.com/search?q=central+pneumatic+61454+capacitor ..

Question moved from MISC to Air Compressor. If you have a maker name, add it to the beginning of this Search Query and them look at the Image tab and find yours. https://www.google.com/search?q=air+compressor+pump ..

Without more info or knowing your compressor my first question to you is,is the oil cooler clean and does the unit have good water flow. DO you have good water flow / pressure. The oil level should be about half way the sight glass running loaded. If the oil level was low ,when the thermostat opens it allows oil to flow to the cooler which lowers the oil level.Typical problems during this time of year are , , dirty oil cooler, Faulty thermostat, Faulty element temperature sensor, Low oil levels and bad oil. Also dirty oil filters restrict oil flow and can cause high element temp. problems. Try back flushing the water side of the oil cooler. Have you checked to make sure the water solenoid is opening. May have a bad coil or valve. May also have water solenoid plugged with something. What is the cooling water inlet temp and outlet temp. The W usually indicates water cooled. If not water cooled, most of the above also applies to air cooled units. just replace water with air if it fits.

like all things from them or used, or new off ebay or amazon or googling with P/n first get the manual with part list the find part there and search online these steps work for mos things not too not china direct junk top brand names not nonames (like ) po - ? - p?

Mon compresseur atlas coco ZR 750 pr?sente comme alarme ?l?ment 1 Outlet temperature

Use the gargler to calculate it for you.

go to hardware store

Try this site:
https://www.manualslib.com/

Did you ever get a manual?

Do you still have the Manual or where did you post the pdf?

Turn black knob to prime, to left! It should prime in about 1 to 2 mins, it will labour a bit, make sure the paint is flowing through the little clear tube , when it does it's primed! Then turn the knob to the spray mark, the spay length of tube ( usually red color) will vibrate a little bit, the spray gun is now ready to use, (gun on spray also). And spray away! Use water based paints its easier to clean! When done put inlet tube, with filter in a 5gal bucket of water turn to prime, then spray and run the 5gals of water through the spray gun this will also clean pump, hoses and and gun at the same time! When dry wipe nozzle of paint gun with a cotton cloth and remove any dried paint, make sure the needle is clean! Pull trigger a couple of times and observe the needle fit in the nozzle, clear hole etc! Regards Jeff Pp lent mine out to another contractor and now I have a priming problem! Never cleaned it right! So that's my next job, cleaning all the bearings to make the bearings seat properly and stop it sucking air! word of advice never lend your tools out! Unless there prepared to buy a new one to replace it!

IF you did what I think you did (as I did) the switch basically falls apart in your hand on on floor as you loosen the 4 screw that holds the spring loaded switch together. I was able to figure out how it reassembles but yet to put it back together for time sake. I plan to bench assemble the PS this week. IF all goes well I will post the results with some pictures. Stand by until then.

remove from power, it is ac there no stored energy, but you can take a screwdriver and place across terminals if you are concerned.

This can be caused by a few different things - first, check the date stamped on the bottom of your fuel cell, just because you just bought them doesn't mean they aren't out of date. Second - check the spark wire for cuts or breaks in the insulation, that could short it out prior to the spark plug Third - make sure the work contact element isn't bent preventing it from traveling fully

Question moved form Sewing Machines category. None available online, just videos. https://www.google.com/search?q=aeolian+pixie+compressor+manual+pdf ..