20 Most Recent Belling XOU174 Electric Single Oven Questions & Answers

0helpful
1answer

Belling synergie main oven not heating

1.Even a bad relay door switch will hinder your oven from operating. If your oven has internal fuses, a wiring or component problem could have caused a fuse to blow. A blown fuse is an indication that a component has shorted or failed, and the problem will need to be corrected. Most ovens that use fuses will have an indication of the circuits that are affected by a particular fuse. If an oven fuse has blown, then you should inspect the oven element and the associated wiring to determine the cause before replacing the fuse. THINGS TO CHECK: the broil element is the heating element that is found at the top of the oven and produces a very high heat for broiling. If the broil element isn't working, you should first do a visual inspection for signs that the element has blistered or separated. If the element appears normal then you can check for continuity with a multi-meter. Remove power from the appliance before performing this test. Remove the back panel and locate the terminals for the broil element and inspect the terminals and wires for signs of overheating or damage. If there is no continuity then the element will need to be replaced. If the wires are damaged then they will need to be repaired. If the element is ok then you will need to check the broil circuit to determine the cause. This involves live voltage checks and should only be performed by qualified persons. Components to check include fuses, if the range is equipped, and oven control thermostat or electronic control. Depending on the manufacturer of the element, you will normally read between 19 ohms and 115 ohms The bake element is the heating element that is found at the bottom of the oven. Most electric ovens use both the bake element and the broil element in a bake cycle, with the bake element performing 90% of the heating. If the bake element isn't working, the oven may not heat. To help determine if the bake element is defective you should first do a visual check. If the element is blistered or separated then it should be replaced. If the element appears to look normal, then turn the oven on to a bake function for a minute and then turn it off. Check the element for signs of heating and if it is still cold then it may be defective. Disconnect the power and then remove the back panel. First check the wires as they may have become loose or corroded. If the element appears to be fine visually, test it for continuity with a multi-meter. ( by placing the each of the meter prongs on each end of the heater element connectors) If the element is burned or no longer has continuity, it will need to be replaced. Depending on the manufacturer of the element, you will normally read between 19 ohms and 115 ohms The oven safety valve (also called the gas valve) is the part that ensures that gas is not released until the igniter has reached the correct temperature needed to ignite the gas. While this part can fail, it is uncommon. If the hot surface igniter does not glow you should first verify that you have voltage to the circuit. This is a live voltage check and should be performed by a qualified person. If voltage is lost at the valve terminals then you should verify the continuity of the bi-metal in the valve using a multi-meter.
5/3/2015 6:10:05 AM • Belling XOU174... • Answered on May 03, 2015
0helpful
1answer

Only two hobs heat up

Surface burners are typically either a coil type, solid type or a ribbon coil as used in smooth top ranges. All of these consist of a heating wire that uses electric current to produce heat. Coil type elements can be checked for continuity by removing them from the terminal block and testing them with a multi-meter. You should also inspect the terminal ends for signs of heat damage or corrosion, and if present, you should replace the terminal block or receptacle at the same time. You will need to remove power from the range to change the terminal block. Solid elements and smooth top elements require raising or removing the main top to gain access. You will need to remove power from the range before lifting the main top. Continuity can then be checked with a multi-meter, once you have removed the wires from the element terminals. On modern electronic control ranges, the oven temperature sensor is the part that regulates the oven temperature. If it is not working properly it could be the reason why the range or oven won't start. This part can be found inside the oven on the rear wall near the top. Most modern ovens will display a fault code if the oven sensor is at fault. If you think the sensor may be the issue you can check the resistance with a multi-meter but will need to know the correct resistance of the sensor at room temperature. Remove power from the appliance before performing this test. The infinite switch on the control panel controls the power to each surface element. If you have no heat at an element and the element and terminal block check ok, then you may have a defective infinite switch. Disconnect power to the range and remove the console back panel. Locate the switch and check for overheated wires or faulty terminals first. Test the switch's contacts for continuity with a multi-meter. If defective, replace the switch. 1.If the infinite switch does not appear to be defective, then you should check for proper voltage to the switch. This is a live high voltage test and should only be performed by qualified persons. (Locate the suspect switch for testing. Label all wires and terminals before disconnecting. A close up digital photo may be helpful. 2.On the burner control switch the terminal labeled "P" leads to the burner indicator light. The terminals labeled "H1" and "H2" lead to the burner element and the terminals labeled "L1" and "L2" (sometimes "N1" and "N2") are the power supply wires. 3.Set your multimeter to ohms setting x1. Turn the burner control to the highest temperature setting. Place one probe on pin "L1" and the second probe on pin "H1". The resistance measurement should be very low, zero to twenty ohms. If the test shows high or infinite resistance, the burner switch is defective. 4.Repeat the step above for the terminals "L2" and "H2". 5.If the control passes that test, turn the temperature setting to about the middle of the range and repeat the previous two steps. This will test for an intermittent problem with the switch. If the test does not show continuity with very low resistance, the switch should be replaced. 6.With the switch turned to the "Off" position, the resistance on each of the pairs of terminals tested above should now show no continuity or a reading of infinite resistance. 7.A test for continuity between "P" and "L1" when the burner control switch is on should show continuity. The light should be on whenever the control is turned on. If your test shows continuity, but the light does not operate, it is likely the bulb has failed. If the burner switch shows high or infinite resistance, the switch is not passing along current to the burner and so the switch should be replaced. ) Most modern ovens use an electronic control board to control the oven functions. These models will use the control board to operate the oven safety valve on a gas range or oven, and the bake and broil elements on an electric range or oven. If there is no power to the igniter circuit, or the element circuits, then you should check the control board to verify that there is power at the appropriate output relay. These are live voltage checks and should be performed by qualified persons only. If there is no output voltage then the control should be replaced. The oven burner igniter commonly known as the hot surface igniter is used in modern gas oven burners to open the gas valve and to ignite the gas. As the igniter draws electric current it will heat to a high temperature and glow, as well as cause the bi-metal in the oven safety valve to warp and open the valve releasing the gas to be ignited. This sequence normally takes about a minute. Igniters come in both flat and round styles and are very fragile. If the burner does not light then you should check the igniter first. If the igniter does not glow at all, then check for power to the circuit. This is a live voltage check and should be performed by a qualified person. If power is present then the igniter may be open circuit and can be checked for continuity with a multi-meter. If the igniter is glowing, but the burner is not lighting, the igniter may be weak and still be at fault because it requires a certain amount of current draw to open the valve. This check requires the use of an amp meter and should be performed by a qualified person. If the igniter is defective then it must be replaced. : I offer free advice bcuz God is so good!
5/3/2015 6:04:26 AM • Belling XOU174... • Answered on May 03, 2015
0helpful
1answer

How to find the serial number in built in oven

usually located in the lower drawer or the door when u open it should see a sticker with number
5/3/2015 6:03:50 AM • Belling XOU174... • Answered on May 03, 2015
0helpful
1answer

Led display not working

I would imagine that the cooker has an internal battery that powers the clock when the oven is not on mains power - since these are so old now, the battery, if THERE IS ONE NEEDS REPLACING.
9/8/2014 12:19:49 PM • Belling XOU174... • Answered on Sep 08, 2014
0helpful
1answer

I need a wiring diagram for this model. Can you help please??

Electro help Try this site. Sometimes, it might help you. Surf the site with patience.
6/7/2014 8:33:19 AM • Belling XOU174... • Answered on Jun 07, 2014
0helpful
1answer

Belling synergie oven - main oven won't come on.

hi

check the timmer clock is not in auto mode as this will stop the oven from turning on. if clock ok then fault could poss be the thermostat
hope this helps you

regards dan
4/19/2014 1:44:07 PM • Belling XOU174... • Answered on Apr 19, 2014
0answers
0helpful
1answer

Vulcan Comenda VC200 Wiring Diagram Series:

Hi i have a belling DF951 fan oven .the heater element stays on when the oven is switch off .Is it the thermostat that is faulty because i can not leave it on .I HAVE TO SWITCH THE MAIN SUPPLY OFF.Or the oven stays on all night
8/28/2013 6:03:04 PM • Belling XOU174... • Answered on Aug 28, 2013
0helpful
2answers

Belling Synergie fan oven.

the elemet has burned out round the fan
8/28/2013 5:56:54 PM • Belling XOU174... • Answered on Aug 28, 2013
0helpful
2answers

Belling built in fan oven (XOU60FP)is overheating

Have same problem, I am repairing our 648HM double oven. Top oven overheats. I am an electronics engineer. I found that top oven fan has failed, this is the first thing to replace. The grill element also failed which maybe due to the overheating oven. NIGEL








4/16/2013 3:36:55 PM • Belling XOU174... • Answered on Apr 16, 2013
0helpful
3answers

WIRING FOR AN ELECTRIC COOKER (I NEED A DIAGRAM) !!!

Trying to wire up an electric oven. Good with electrics, normally. Sounds stupid bus there are no holes to place the wires into on the oven panel. In other words not like the speces on a plug or on the main live circut on the wall. Where do I put the wires????
3/26/2013 3:45:14 PM • Belling XOU174... • Answered on Mar 26, 2013
0helpful
2answers

How do I find the model number on belling synergie oven?

I have the same problem. I have inherited a Belling Synergie multifunction double oven. The Model No is worn out - yet there is a specification 492SS which isn't. I am going to purchase the element with this number and hope this works.
10/19/2012 4:14:01 PM • Belling XOU174... • Answered on Oct 19, 2012
0helpful
1answer

Belling cooker d841 top oven

The US National Electrical Code only mandates white (or grey) for the neutral power conductor and bare copper, green, or green with yellow stripes for the protective ground. Power will generally be black or red. 3 phase power will have three colored lines, the first is generally black or brown, the second red or orange, and the third blue or yellow..i,e,Yellow/Green is Earth so 'E'. Brown is live so 'L', and Blue is neutral so 'N'.
5/8/2012 11:09:21 PM • Belling XOU174... • Answered on May 08, 2012
0helpful
1answer

Replaced element on belling synergie

fan on in oven but not heating up just after the power tripped think because of oven this is not the first time this has happened can you help please


yours shane
11/21/2011 3:41:53 PM • Belling XOU174... • Answered on Nov 21, 2011
0helpful
2answers

Fan making loud noise

Hi

does the noise start as soon as you turn the fan oven on?
does the noise stop as you turn off?
just depending what make and model you have there is two fans
in it 1 is the fan motor inside oven at back and other
is the cooling fan which is at top of oven .you just need
to find out which one it is and just replace . then should be back to normal

regards dan
5/4/2011 6:20:09 PM • Belling XOU174... • Answered on May 04, 2011
tip

How to diagnose, fit and change a Belling fan oven element


If your fan oven is not heating up properly the Fan Oven Element for your Cooker is usual culprit. Fitting an oven element is generally very easy, as demonstrated by The Apart4u video on How to change repair and replace your fan oven element:this fan oven element can usually be changed without taking the appliance out of situ.

0helpful
1answer

The oven is coming on but not heating up

check for proper power then if you have it replace control board
5/6/2010 5:39:33 PM • Belling XOU174... • Answered on May 06, 2010
0helpful
1answer

My oven wont heat up

More than likely a faulty oven elementr.
This is located at the reae of the inner oven compartment behind a removeable cover.
4/9/2010 9:06:49 PM • Belling XOU174... • Answered on Apr 09, 2010
0helpful
1answer

The fan is working but the oven isn't heating up.

sounds like the oven heating element is defective, shout be about $150 to repair, less if you do the work
7/14/2009 4:23:05 PM • Belling XOU174... • Answered on Jul 14, 2009
Not finding what you are looking for?
Belling XOU174 Electric Single Oven Logo

45 questions posted

Ask a Question

Usually answered in minutes!

Top Belling Ovens Experts

Harrie

Level 3 Expert

6746 Answers

RudeRude

Level 3 Expert

526 Answers

ADMIN Canada
ADMIN Canada

Level 3 Expert

40079 Answers

Are you a Belling Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Belling Ovens

  • Belling Ovens

Most Popular Question

oven wont heat up

  • Ovens
Loading...