20 Most Recent Belling XOU270 / XOU271 Electric Single Oven Questions & Answers

0helpful
2answers

Belling Synergie

NEED NEW FAN OVEN ELEMENT THAT CAN BE FOUND HERE You need Element code AB20 on link belowhttp://cookerandovenelement.co.uk/bellingfanovenelement.htmlelement is located on back wall of oven you need to pull oven oven to remove the element element is held by two nuts from back and i screw from front
12/24/2012 7:11:21 PM • Belling XOU270 /... • Answered on Dec 24, 2012
0helpful
1answer

I turned on the oven last night & it tripped

you need to upgrade your beaker
8/13/2011 7:10:28 AM • Belling XOU270 /... • Answered on Aug 13, 2011
0helpful
1answer

No heat from oven although fan and light are both

hello gavin..... Usually, when an oven won't bake, it's because the bake element is burned out. The bake element is the black, pencil- thick tube at the bottom of the oven. When the oven heats, the element glows red. This element has an expected life-span of several years. It may last for only one; it may last for many more. When the element burns out, you need to replace it.

This is an inexpensive part and relatively easy to replace. Call your local appliance store to obtain the part and the instructions on how to install it. Joe

Thanks for choosing Fixya!
1/5/2011 8:19:13 AM • Belling XOU270 /... • Answered on Jan 05, 2011
0helpful
1answer

The oven stopped working but



Hi,


If your electric oven is taking too long to heat or just not heating up right, then check out this tip that will give more detail about your problem.

Oven Problems Electric Oven is Heating Slowly or Poorly

heatman101

12/25/2010 1:10:36 PM • Belling XOU270 /... • Answered on Dec 25, 2010
0helpful
1answer

Just had heater element tested and its ok,oven

Yes the thermostat is the most likely problem, you can easily replace it.
12/11/2010 1:13:48 PM • Belling XOU270 /... • Answered on Dec 11, 2010
0helpful
1answer

The oven stopped working so I replaced the oven

Re:The oven stopped working so I replaced the oven element (ES101150) successfully. Now a year later the grill has stopped working so I replaced the grill element (ES548158).

The first success had been a lucky dip. before replacing an element you have to read Ohms at element, if reads infinity (open) replace it, if not, read volts coming from timer board.

Re:Now the fan, the oven, the light and the grill all don\'t work but the timer still works. Is there an internal fuse somewhere ?

There is no fuse. Depending on the country of use, the power cord may be fused, but if the timer is working, that is not the problem.

The grill element should be a double element in this model. Grab the old grill element and read Ohms, to find out if the old one was open. If one of the elements was open, then the element was bad. If it was not , then there was a different problem causing no heat. The circuit comes from timer board, passes through temperature sensor and powers fan and element. The job is done reading Ohms to find out if there is an open in wiring to grill, and if there is none, reading Volts at OEC (oven timer) contacts to find out if timer is working (timer is expensive).

Parts for this oven are scarcely available from third party, better ordering from manufacturer through the number listed on the owners manual.
8/29/2010 9:51:20 AM • Belling XOU270 /... • Answered on Aug 29, 2010
tip

How to diagnose, fit and change a Belling fan oven element.


If your fan oven is not heating up properly the Fan Oven Element for your Cooker is usual culprit. Fitting an oven element is generally very easy, as demonstrated by The Apart4u video on How to change repair and replace your fan oven element:this fan oven element can usually be changed without taking the appliance out of situ.
0helpful
1answer

WHY CANT I TAKE ELEMENT OUT

If you cannot remove screws from inside oven compartment, then, yes, it will be neccescery for you to remove the oven from it's housing to gain access to the screws from the rear.
5/4/2010 9:24:07 PM • Belling XOU270 /... • Answered on May 04, 2010
0helpful
1answer

Cannon 10287G gas - lower oven flame no longer

Nope- It's most likely the ignitor. Resistance should be above 4ohms. Accessible below drip pan. 40-75$ local app. parts store. Hope this helps- ED
3/15/2010 7:31:50 AM • Belling XOU270 /... • Answered on Mar 15, 2010
0helpful
1answer

My hob is working but there was a bang in the oven

If it is a fan assisted oven, and the fan is working o/k, then I would suggest that you fit a new oven element, if the fan is not working, then you are going to have to investigate further.
Please rate my solution.
Thanks.
11/8/2009 10:48:03 PM • Belling XOU270 /... • Answered on Nov 08, 2009
0helpful
1answer

The fan assisted oven has stopped heating up how

If the fan is working o/k, then you needs to replace the oven element located at rear of oven compartment.
Please rate my solution.
Thanks.
10/29/2009 8:23:57 PM • Belling XOU270 /... • Answered on Oct 29, 2009
0helpful
1answer

Oven will not heat past 100 degrees

More of a clarification request:
Is the oven remaining on all the time(oven light stays on)and the temp not going above 100 ,or is it going to 100 then switching off?
8/10/2009 10:56:01 AM • Belling XOU270 /... • Answered on Aug 10, 2009
0helpful
1answer

Replace Bottom Element in Belling XOU270

If this is a fan assisted oven, then there is no bottom element, only the fan element..
Remove the panel at the rear of the oven, there you will see the element, remove any screws that you can see and pull element towards you, disconnect the leads, don't loose them, and replace element.
If no screwws are visible then you will have to remove the oven from housing and do it all from the rear of the oven. Make sure power is off before you do anything.
Good luck.
Plz rate my solution.
Thanks.
12/16/2008 4:18:23 PM • Belling XOU270 /... • Answered on Dec 16, 2008
0helpful
1answer

Cooker is a Belling XOU270 / XOU271

You need to replace the fan oven element.
12/16/2008 3:03:24 PM • Belling XOU270 /... • Answered on Dec 16, 2008
0helpful
1answer

How do I remove front control panel on electric Belling induction oven

Hey Kevin, thank you for the question. Can you please provide us with your model number, we will assist you better.
9/24/2022 6:24:01 AM • Belling Ovens • Answered on Sep 24, 2022
0helpful
1answer

I have a Belling fan oven that's not heating up

during cycling see if voltage to ignitor
8/28/2022 9:59:04 AM • Belling Ovens • Answered on Aug 28, 2022
Not finding what you are looking for?
Belling XOU270 / XOU271 Electric Single Oven Logo

27 questions posted

Ask a Question

Usually answered in minutes!

Top Belling Ovens Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

Lawrence Oravetz

Level 3 Expert

10558 Answers

Gil Shultz

Level 3 Expert

3464 Answers

Are you a Belling Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Belling Ovens

  • Belling Ovens

Most Popular Question

belling synergie

  • Ovens
Loading...