20 Most Recent
Konica Minolta Bizhub C452 Copier - Page 2 Questions & Answers
Error code C2257
Cleaning motor, motor functions to route old toner to waste toner box, motor located lower left side rear. Open close front door to reset if code comes back motor is bad or have a bad board. But first remove the transfer belt and check it cleaning system also the waste toner box, might have some toner that has harden and is not allowing motor to turn recommend get a KonicaMinolta tech to look at it. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
C-3B02 in bizhub c452
This going to get expensive, could be any of the following the IH coil unit or IH Power supply unit. This series of machine uses a magnetic field to produce heat for the fusing process the process of fusing the toner to the paper, any way the code you have is stating the IH pwr sup or coil unit are not talking to the copier cpu. It could also be a relay board between the cpu fuser system, worse case the image control board. I would go with fuser power supply. Just my humble opinion. Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
I have a C - 3921 trouble code in Konica Minolta c451
Replace the fusing unit. Reset the copier power off the machine, with the utility/counter depressed power on until trouble reset appears, touch it see OK. Power off wait 10 seconds power on. if no code ok, if code re-appears do NOT Reset, machine is telling you it is broke if you reset again it can catch on fire the code you are messing with the is the fuser the hot part, it will ruin a perfectly good day. Get fuser replaced. about 800.00 Btw, I’m available to help over the phone in case u need at
https://www.6ya.com/expert/normanj_7893313f0751935f
Problem in turning on the konica c452
i have konika c452, after a while it doesn't turning on , service man check all the boards but it wasn't enough . please help me to find a soloution
C163 on b52izhub c5
3B02,3B03,3B04 - IH malfunction.Try reset the error code:
Turn OFF the copier,press and keep pressing the Function key and turn ON the copier.Keep pressed the Function key until appaire the Trouble reset message on the display.Release the Function key ,touch the message and turn OFF the copier.Wait 1 minutes and turn ON.
Hi
I need a help i hav error code C-8003 on konica Minolta B951. Please assist.
Thanks
Podtermistor wa?ka utrwalaj?cego nie
wykrywa wymaganej temperatury w ci?gu 30 sekund.
po rozpocz?ciu cyklu rozgrzewania; dlatego
kopiarka nie ko?czy cyklu nagrzewania.
• Temperatura wa?k?w utrwalaj?cych nie
osi?ga wymaganego poziomu nawet po
up?ywie ustawionego czasu podczas cyklu nagrzewania.
1
Sprawd?, czy lampka utrwalacza H1 zapala si?, gdy g??wny
wy??cznik zasilania jest ustawiony w pozycji W?., w razie potrzeby popraw lub wymie?.
- -
2
Sprawd?, czy H2 w??cza si?, gdy g??wny
wy??cznik zasilania jest ustawiony w pozycji ON, i w razie potrzeby popraw lub wymie?.
- -
3
Sprawd? instalacj? TH1 i TH2 i
w razie potrzeby popraw lub wyczy??.
- -
4
Sprawd? dzia?anie TH1.
Usu? CN80 (4P), a nast?pnie sprawd?, czy rezystancja
na CN80-2 i -3 na termistorze jest
niesko?czona.
- -
5
Sprawd? dzia?anie TH2.
Usu? CN81 (4P), a nast?pnie sprawd?, czy rezystancja
mi?dzy CN81-2 i -3 na termistorze jest
niesko?czona.
- -
6
Sprawd? ci?g?o?? H1.
W razie potrzeby popraw lub wymie?.
- -
7
Sprawd? ci?g?o?? H2.
W razie potrzeby popraw lub wymie?.
- -
8 Zmie? PU1 - -
9 Zmie? PWB-A
Not finding what you are looking for?