20 Most Recent
Creda W120VW Front Load Washer - Page 3 Questions & Answers
It makes a noise as if its spinning but the drum
Hi,iI have just had the same fault, and as described elsewhere, the
solution was to replace the motor brushes. I would say this took 1/2 -
3/4 hour to remove brushes and same to replace.
How:
1.DISCONNECTED ELECTRICITY SUPPLY
2. Disconnected water
3. Removed the 1 screw from back panel, removed panel to get access to remove belt.
4. Lay washer on it's side (2 people recommended)
5. From underneath machine, unscrewed 2 bolts on the motor (back of the machine)
6. Holding the motor so it did not fall and get damaged, carefully
tapped end of motor to unmount it from holding pegs (slides towards
back of machine)
7. Noted how the plastic cover fixed to motor, then snipped tie wrap holding it to motor.
8. Unplugged connector and earth connector.
9. Carefully removed connector on each brush.
10. AS THE BRUSH WAS SLOWLY WITHDRAWN, checked the orientation of the
bevelled edge of the brush relative to the motor so the new one was
fitted correctly (the end of the brush is angled so it sits flat
against the motors commutator)
11. Replaced brushes and refitted in reverse order.
Take care
How to change a door seal
Look on You Tube for replacing door seals, there are a couple of videos on there that will show you how. All door seals are basically the same for fitting so this will be a good guide.
I have a creda excel 1200 the other day the water
Remove back from machine, dissconnect motor plug from motor, then turn machine on, if electric trips then you know motor is ok so place plug back into it, then do pump, and so on untile something is disconnected and fuse wont trip. Make sure you do not have machine connected to power supply while removing wires, also that wires do not come into contact with anything when disconnected. And dont remove Any earth wires
The suspension spring came undone and fell accross
That sounds like you have right idea. Call your service provider and give them your model and serial number of your washing machine and they can order you a new board. Unplug your washer and switch the board wire for wire.
Blue thing on the drum for tumbling the clothes
The part you are referring to is called the clothes or drum lifter.
The only solution is to replace it with a new one, they click into slots in the drum, and the locating lugs on yours have probably broken or twisted out of alignment.
Please rate my solution.
Thankyou.
No power
The only way to be certain if you have actually got power at the washer, is by removing the top cover, and checking for voltage at the terminal block
If you have power, then could be faulty door lock, or you have not fitted the door handle correctly.
Hope this helps.
My door lock
Could be a weak or broken spring in the door handle.
Failing that, then it is likely to be a control board problem.
I have a Creda 1200 washing machine, I am unable
The filter is at the rear of the washer.
Remove the lower rear cover of washer.
Remove the large black hose fastened to bottom of drum.
Clean plastic filter inside hose.
Remove hose onto pump, and check for blockage or obstruction here as well..
Please rate my solution.
Thanks.
Noisy drum on even moving by hand
It is definately the main drum bearings that have failed
To be honest with you , if the washer is more than 4 or 5 years old, you would be wise to call it a day, and purchase a new one, as it is an expensive job to put right..Sorry to bring you doom and gloom.
Merry xmas
Fit a new door hinge
Remove the wire clamp securing rubber seal to front of washer, pull seal of front of washer, this will give you clear access to tjhe door hinge, ondo the 2 screws securing the door hinge, remove door ,and seperate the 2 door halves by removing the screws securing it together
Replace with new hinge, fit back in reverse order.
Please rate my solution.
Thanks.
Drum not running
Seems like a broken belt - most dryers have a safety device that shots circuit off to the electric element/gas unit when the belt breaks and that is the reason why your dryer isn't heating up.
Good luck
It doesnt seem to be pumping the water out when it
Check the drain hose.
If you find nothing in there unplug the drain pump and check if the hose attached to the pump is clogged (unplug appliance first).
If that does not fix the problem, it can be a faulty pressure switch , a faulty drain pump, or a problem concerning timer board.
In that case consider calling a techician.
Drum does not turn
hi there just a few things. was the washer making a huming when was on a spin ? i have only had a few were the bearing have stoped the washer from spining i would say look at your brushes 1st as this is a lot easy then doing the bearings. if i a new set of bearings are needed i would give your self a good few hours as some one me can do them in one and a half hrs but i do 10 plus a week make sure you mark were the wires go and just kake your time maring down were things go and good luck stuart
Not finding what you are looking for?